Network Security Audit Tool
Hi I am looking for a tool for auditing all the cisco and non cisco devices. Please kindly Advise. Thanks
View Article13.4 DHCP Relay
Hi all,In order to avoid conflict with other ips in the vlan you could also use:ip dhcp ping packets 1This would get the server to ping the ip address before assigning it to make sure nobody else is...
View ArticleFCOE lab help
I need some assistance with this if someone can tell what I did wrong based off the outputs. I checked my configurations against the FCOE lab in the workbook and everything appeared to be spot on. I...
View ArticleLLQ Servicing
Hi everyone,This question regarding LLQ has been bugging me and I have not been able to find a clear answer.Suppose I have a LLQ and three CBWFQ's. Congestion occurs and all of the queues begin to...
View ArticleDoes the Route Reflector modifies the TTL value of a packet ??
Does the Route Reflector modifies the TTL value of a packet ??.... Say a route comes in from an eBGP peer to the RR and then goes to the RR clients. In this process the next-hop value is not...
View ArticleNAVIGATING THE DOC CD
I am new to the www.cisco.com website and have had difficulties locating the correct IOS release for the ccie route switch lab exam. Please offer links and any advice to assist in becoming more...
View ArticleTask 2.5 IGP Redistribution
Task 2.5 tells us to redistribute various routing protocols. The solution on R3 is listed as follows: R3:router eigrp 100redistribute rip metric 10000 1000 255 1 1500!router ripredistribute eigrp 100...
View ArticleClik here to view.
[Offer] Access INE Rack - Faster INE Lab Practice
I'm preparing for CCIE SP exam. The problem I'm having difficulties in practice INE lab: slow and laborious manipulation. So, I code a tool for supporting my work.Today I share this tool for you. You...
View ArticleSP Workbook - Full Scale Lab 2 Task 1.1
I'm assuming that the Task 1.1 "solution" is either partially wrong or there is a typo. Maybe I'm wrong?On the two trunk ports connecting the switches (fa0/20 & fa0/21) shouldn't both VLAN 9 and...
View ArticleNTP
Does anyone know the difference betweenServeServer-onlyMy understanding Serve - Allows time requests and NTP control queries, but does not allow the switch to sync itself to a device whose address...
View ArticleCisco Library 360 is recommended?
hello everybody, im asking to the community if anyone has used in their studies the cisco 360 reference Library, for example for the ccie written exam, or even for the lab?Checking this, i coud know...
View ArticleIOS-XR LDP label weirdness
I'm doing Full Scale Lab 4 and found something strange:routes---XR1------XR2Both XR1 and XR2 are peering via ISIS and LDP via their POS interface.XR1 is doing redistribution of some routes from BGP...
View Article8.3 Congestion managemetn
Ok guys, WTF???I understand that you need to calculate the fragment size using the physical access rate but I don't understand why the CIRs were changed from 384000 to 512000. Anyone???
View ArticleCCIE Security v4 Home LAB ( Cost Effective )
Hi Please i need advise on building Security LAB home lab. Thanks
View ArticleWB Full LAB4 task 4.1
I was doing this task when I configured XR1 for IPv4 Labeled-unicast with R3, XR1 stopped sending routes just it's own Loopback although it recieves all iBGP routes normally !! I spent like 30 minutes...
View ArticleNeed Help with Task 4.1 on SP Full Scale Lab 4
Hi All,I am running into a problem on Task 4.1 on Full Scale Lab 4. I've spent hours on this and can't figure this one out. The short story is that during this task, R5 is not able to learn labels...
View ArticleInfo on Implement Server load balancing in HA mode
I haven't seen anything on Cisco's site that says ACE server load-balancing is removed, so I'm still going to study for it. In all, the blueprint topics cover some very basic stuff. I've been able to...
View ArticleSVS Domain
Hi,I have a quesiton about Nexus 1000v. If you have more then 64 hosts then you need to run a 3rd (or 3rd and 4th) VSM. Does this new VSM use the same or different domain id? ThanksJason
View ArticleChassis IOM ports on UCS
Hi, can anyone tell me why my physical ports on my IOM/FEX modules are showing as 'up' when nothing is plugged into them?I have 2104XP IOM's and only ports 1 and 2 have connections. But when I look in...
View ArticleSecure CRT issue
Hey guys, have you ever had a problem with SecureCRT while you are setting up a device ?Sometimes the securecrt change my keyboards letters of the default configuration, you know ? Like, My ? begins to...
View Article