Mobile Connect/SNR CLI sent to PSTN
Hi All,I am going through Workbook 1 (task 13.3 Mobile Connect Localisation) and seeing some behaviour that I don't understand. The scenario is this:call from PSTN phone +15126026223 into DN 1002 on a...
View ArticleTask 2.2, R5 using RIP routes
I just wanted to check, is there any reason to change the AD of RIP as in the solution guide vs using the backdoor command under BGP?network 205.90.31.0 backdoor network 220.20.3.0 backdoornetwork...
View Article2.2 Alternative solution
The solution I came up with for this task is to tag the routes redistributed from RIP to EIGRP on R6 with a tag and then deny this tag with distribute list under the OSPF proccess on R1 and...
View Articlevol2 lab3 2.2 question
guys: 2.2 has the following 2 requirement: 1. R5 should route through R1 to get the prefixes learned from BB1.2. R5 should route through R2 to get thr prefixes from BB3. I think the solution only...
View ArticleCCIE Voice to become new CCIE in Nov '13
See my blog article for more news, and also see comments for further insight.
View ArticleRSTP TC notifications
Cisco states that with RSTP configured that only nonedge ports moving to the forwarding state generate a TC BPDU.What defines a port as edge or non-edge? Portfast?
View ArticleClik here to view.
FWSM Question - Lost connectivity to shared mgmt interface
Background:We have Cisco 6500 Firewall Service Modules with multiple contexts and shared management interface. The FWSM has a secondary module, every context has its own management IP address along...
View Article14.3 no pop label for 150.1.4.4/32 on R5 and R6 after applying the filter
HiAfter applying the access-list on R4 , R5 , R6 .. I can not see pop label for 150.1.4.4/32 on R5 and R6.Please advice Rack1R4#sh run | sec mplsmpls label protocol ldpmpls ldp neighbor 150.1.6.6...
View ArticleSwitchports Admin Down
Seems like everytime I log into a rack 3 of the interfaces on each switch is admin down. I don't know if that is part of the configuration I am supposed to fix or if that is the topology I am supposed...
View ArticleSr. Network Security Engineer Opening
Location MD-SuitlandPosition Direct Hire- W2Schedule Full TimeU.S. citizenship is required and the ability to qualify for a Public Trust clearanceJob Description:Systems Security Engineer position...
View ArticleTask 1.5 - Rate Limiting (Storm Control)
Hi Everyone,For this task, I multiplied out the "average" packetsize by the "average" number of packets per second, and used that value (1.908 Mb/s) as the bitrate for the storm control. The SG...
View ArticleBGP ROute reflector problem
R1(.1)<-----172.16.10.0/24----->(.2)R2(.2)<----172.16.20.0/24--->(.3)R3 R2 is Route reflector , R3 and R1 are clients. When I advertise loopback 1.1.1.1./32 on R1 , it shows on R3 as...
View ArticleClik here to view.
Regarding IP communicator
Hi everyone, I am using Cisco IPC to to get registered with my CUCM 8.6 , but my IPC not registered and its showing Blurred screen(its not allowing to change TFTP and ADapter settings)...
View ArticleCCIE RnS Version Change to 5 by 2013 End ?? Any Information
hello everyone , I just wanna know about the version change of RnS track ??When Cisco will announce & when its gonna change ver 5 ( new bluepint ) What New things are expected to get changed . If...
View ArticleCan someone explain me what is TLV?
I have done research and know somehow, but it is difficult to understand. I mean why ospv3 and ISIS took the benefit from TLV?
View ArticleTask 2.2 OSPF - Why "ip ospf network point-to-point" on R5's S0/0/0 FR...
Hi Experts,The SG for this task specified "ip ospf network point-to-point" under int S0/0/0 of R5 and R4.Is this requirement mentioned in the task? Am I missing something?ThanksAlex
View ArticleTask 2.1/2 - OSPF N2 to E2 Translation
Hi,Just wanted to point out that in addition to what's explained in the SG, one of the ABRs in Area 1 will be actually installing the route to 150.1.8.0/24 as E2.Since there's a GRE Tunnel between R2...
View ArticleTask 3.2 OSPFv3 summarization typo
The task says to do summarization on R1 but should be R2. Solution shows config being done on R2.
View Article