Task 3.1 Friendly Link Local addresses
I noticed in the SG that friendly link local addresses were used e.g. FE80::1. Clearly this makes the creations of frame-relay maps much easier as you don't have to copy the link local (eui-64 format)...
View ArticleTicket 3.1(Broadcast keyword association)
Hi every one,I would like to ask why SG associate the broadcast keyword to IPv6 Global address i thought it's should be asscoiated with link-local address to allow the adjency to form Regards
View ArticleISE & WSA Primer Course Access for Buyers of CCIE Sec Ultimate Bundle
Hi, As a buyer of ccie security ultimade bundle set that I bought 6 months ago, wouldn't I access to those newly came security primer courses?I cannot see them under my products section and from...
View ArticleQuestion reg. MAC-Address Table static entries
Hello,I'm doing Vol 1 lab and got a question in sec 1.39[Configure stati CAM entry for that MAC address of R6's connection to VLAN 146 to ensure that this address is not allowed to roam]i've configured...
View ArticleQuestions on Task 4.6 of Full Scale Lab #3 for SP
Hi All,I was wondering if anyone has done Full Scale lab #3 and saw these following peculiarities:1. Is it absolutely necessary to remove R1's cluster-id? I was able to get things to work just fine...
View Article7.1 SNMP
Hello everybody.Why, in the solution book, do we enable tty traps for the first server?I cannot find the need for that in the task.
View Articlestandard acl with single entry
Hi, i have got one question where it says that R1 must accept these prefixes from Backbone router.The prefixes are the following10.10.5.0/2410.10.7.0/2410.10.13.0/2410.10.15.0/24And the requirement is...
View Article7.2 IOS MENU
How to exit the menu if you forgot to insert the exit-menu in the configuration?I build the menu but to insert forgot the exit .I decided to test my menu and now I am stuck - I don't know how to get...
View ArticleTask 7.4
I think we need to add preempt for the standby router as well as the active router. I found this scenario in IP Application Services Configuration Guide and its configured as i mentioned.
View ArticleVMNIC vs VNIC vs I/O module southbound ports
Hi all, As a junior of virtualization and ucs, I have some questions about VMNIC , VNIC and I/O module southbound ports (connected to blades).1. In terms of limitation of VNIC in UCS, does it decided...
View Article8.3 Rate Limiting
I just don't see how the wording of the question can bring you to believe that Fa0/1 applieS an outbound policy map .. Another post concerning the topic regarding the confusion:...
View ArticleTask 8.4
Hello, I am confusing compressiong method between stacker and predistor.Cisco Link does not help me to understand...
View Article7.3 DNS - No idea how this works - help required
Hi All,I have read this a few times and cannot make any sense of the SG solution. Why is the alias command entered on the AS? Why in the verification does R5 telnet to the correct address and not the...
View ArticleCCIE R&S Lab for Sale
CCIE LAB--------R1 = 2811, 768/256, 2FE,2SR2 = 2811, 256/64, 2FE,2SR3 = 2811, 256/64, 2FE,2SR4 = 2811, 256/64, 2FE,2SR5 = 2651XM, 128/32, 2FE,4SR6 = 2651XM, 128/32, 2FE,4SSW1 = WS-C3560-48TSSW2 =...
View ArticleAToM
AToM Issue------- I have verified R4 And R5 peer as MPLS-LDP Neighbors also verified the vlan interfaces is (UP/UP)but still the AToM VC is not comming up. Outputs of show/debugs provided. Can any one...
View ArticleClik here to view.
OTV Deployment Options
Hello group, Based on the official document called “OTV Technology Introduction and Deployment Considerations”, I arrived to the four options in the diagram: Now I want to find the pros and cons of...
View ArticleAToM
AToM Issue------- I have verified R4 And R5 peer as MPLS-LDP Neighbors also verified the vlan interfaces is (UP/UP)but still the AToM VC is not comming up. Outputs of show/debugs provided. Can any one...
View ArticlePIM bidir and nbma-mode
I was watching the Deep Dive Multicast video series and made a note that bidir PIM does not support nbma-mode. I wanted to understand this more as I was playing around with NBMA and multicast this...
View Article2.1 Router Rip does not start RIP
Hello,I am using real lab at INE. On router R6 I cannot start RIP. I even reloaded the router. Any ideea? Rack11R6#sh ip protocols Routing Protocol is "bgp 200" Outgoing update filter list for all...
View Articlemulticast ping reliability
Hi All,It s now several times that I run into a strange issue with multicast ping, I am wondering if anyone has witnessed it too and may have an explanation.When doing a simple multicast ping "ping...
View Article