Link queue
Hi experts,R1#show queueing fairCurrent fair queue configuration: Interface Discard Dynamic Reserved Link Priority threshold queues queues queues queues...
View ArticleFailed first RS LAB attempt in Brussels @2013.06.14
Hi,I wrote about my first exam experienc here, check out :)http://internetworking.hu/2013/06/failed-first-rs-lab-attempt-in-brussels-2013-06-14/Gabor
View ArticleFull Scale Lab 3 comments
What a great lab! This is the 1st lab I do that builds up so much complexity, layer by layer. Lab 1 and 2 were good, but this one was just brutal! It 1st hits you with some troubleshooting, something...
View ArticleHome lab - How to cable the BBx routers?
Hi,I dont know if this is the right forum, but I try anyway.I have collected enough equipment to build my own lab, but I'm a bit confused when it comes to the serial-connections.I have an 2811 with a...
View ArticleTask 8.2
The SG shows a policy map configured so that P2P traffic gets dropped between vlans 5 and 52. The task does not state to prevent P2P traffic from going BETWEEN these interfaces, rather it simply states...
View ArticleWFQ working technology
For understanding purposes essentially i have 3 doubts about that technology:1) if the weights of the flows are based on IPP and the IPP are 3 bits the maximum number of combinations i suppose then...
View ArticleMPLS not running Routing Protocol
Hello, I have 1 question, i am sure you SP Gurus can help me. I have been given an MPLS connectivity by my SP. I have 1 HQ and 5 Branch. The SP has terminated the fibre using their own router, and...
View ArticleIPv6 GRE tunnel not working.
Hi Experts,I am trying to create a IPv6 tunneling interface between 2 routers.R1#sh run int tu 12Building configuration...Current configuration : 136 bytes!interface Tunnel12 no ip address ipv6 address...
View ArticleRoutes not exchanging between OSPF neighbors.
Hi Experts,I am running OSPF between all the 3 routers using FR hub and spoke. R1 is the hub.The neighborship is up.R1#sh ip os neighborNeighbor ID Pri State Dead Time Address...
View ArticleGentle Start
Hi folks,I am following Peter's advice and using the gentle start approach. I jus finished Volumn II Lab 1 and compile a list of Volumn I scenarios that I need to go back and practice. Now let's say...
View ArticleSecurity WB1v4 Task 4.4 Unable to integrate ACS with AD
HiHas anyone run into the following problem? When trying to integrate ACS with AD,as per task 4.4 instructions, I always get the following message:"Connection test to 'inelab.local' failed.Further...
View ArticleClearing out Home Lab
Open thread of things that I am trying to clear out. Most of this is my old lab that I have upgraded or moved from over the past year. Everything priced lower than eBay. Just need this stuff gone....
View ArticleSignificance of Double Colon (::) in IPv6 Address
I well understand that: A double colon indicates the part of the address containing only zeroes that has been compressed, to help make the address shorter.However:Does Double Colun (::) in IPv6 Global...
View ArticleNo DTMF over PSTN
Hi my home setup is this HQ -2821/T1SB - 2801/T1SC - 2811/E1PSTN - 3725 hq/sb sb/hq calls over pstn works fine, dtmf is also ok. But hq/sb to sc calls over pstn has loud noise in it. like a distortion...
View ArticleHome Lab Suggestions
I have been able to gather an assortment of equipment for a home study lab for the CCIE Voice. Does anyone have configs or layouts for connecting up a home lab? I plan to use rack credits for some...
View ArticleCCIE RS Bootcamps
Hi INE,Is there any plans to bring down the CCIE Bootcamp to the southern hemisphere any time soon. Cheers,Krishil
View Article11.7 Filtering Fragmented Packets
To me the solution does not match the questions. Q. Ensure R3 prevents fragmented packets from reaching its local HTTP server. The solution basically says allow all RIP messages, deny any fragments,...
View ArticleEIGRP show command
Hi guys . i have a question .... why existing letter "s" in end of the command "show ip eigrp neighbors" whereas not in the "show ip ospf neighbor" commandthanks
View Article2.4 Second bullet wording
Hi,Reading the second bullet in the WB and also the SG for it ... I think there is something to talk about here.So, the WB says : • For the purposes of load balancing and redundancy AS 100 has...
View ArticleQuestion for the Pros
Let's assume we want to show only Received and Missed Calls (in this order) when pressing the directory button while the other phones should show default behaviour. (Missed,Rec,Placed,Pers,Corp...
View Article