Why the low first-attempt success rate?
Hi all,(Sorry if this has been asked before. I did a search and couldn't find anything.)This is something that's been on my mind. Why do so few people fail the first lab attempt? Is it just lack of...
View ArticleClik here to view.
Why does my PBR does not work with OSPF P2M Network Type?
R5(config)#! On R5 I am filtering route to R2's loopback: 150.1.2.2/32R5(config)#! inbound, so Type 1 LSA still exists in R5's databaseR5(config)#!but not in the routing table, let's seeR5(config)#do...
View Articleswitch protected port and voice vlan
Hello,Excited to learn about protected port to restrict bad guys traversing between workstations etc.However, I am concerned that this will break voip setups. I imagine that the phones need to send UDP...
View ArticleQuestions about workbooks and racks
Hi , I have the following few questions which i hope you answer: 1- I saw that the workbook for v4 seems to be available at http://www.ine.com/self-paced/ccie-security/workbooks.htm , can you confirm...
View ArticleASA Radius Authentication section 4 Technologies Lab Workbook
Dears,Please note that i followed the steps in the workbook for the section 4 ASA Radius Authentication. My problem is when i put the username/password, everything works fine but when i enter the...
View ArticleATC Video request
Brian/Chris will it be possible to post the list of videos that are in development for the new ATC...
View ArticleVPN with more than one filter / nested ACL
Dear All, Is there a way to assign more than one ACL to a VPN profile or implement a nested ACL structure? I am trying to avoid modifing a large list of ACLs to insert the same ACE in each ACL bound to...
View Article4.11 RIPv2 Filtering with Standard Access-Lists
Hi Dears As the question stated to filter all routes, thats why we permit 0.0.1.0 255.255.254.255, if we want to be more specific on filtering as per what BB1 is sending ( it sends 4 subnets...
View ArticlePorts on ASIC
Hey All, Having an issue at work with output drops on ports with high traffic flow, using 6513 and 6548 line cards, I know that the port to ASIC grouping isnt great on these so we are having to spead...
View Article1041N
I have an AP 1041N with an old configuration and I cant remember the password though.I am wondering how can I reset it to default configuration, without any configuration ?I've tried to reboot it and...
View ArticleCisco ASA VPN Optimal Gateway Selection with Load-Balancing
Hi all is it possible to use the Cisco ASA VPN Optimal Gateway Selection say for each site that has at least 2 ASAs and than on top of that use the VPN Load-Balancing feature? I have 3 sites in mind...
View Article1400 TOKENS FOR SALE
I have 1400 tokens for sale with 50% discount: 1 token = $0.5 flat rate.Minimal batch is 400 tokens for $200. If you take all 1400 - you'll get $100 off.Please, send me PM (private message) if...
View ArticleLayer 2: What's in/out?
Now that the v5 lab is all virtual, I was curious about what Layer 2 technologies would be on the blueprint vs. the v4. I was a little surprised to see some things I thought would get cut out, like...
View ArticleDMVPN Intricacies
Hello all,So in preparation of learning the VPN's for v5 I have started with l2tpv3 and DMVPN. I am pretty good with configuring these both from scratch, however what I keep thinking is how much detail...
View ArticleDropping packets
I have a scenario of dropping packets in my class-default class under a specified policy-map (outbound) and I can't figure out why. The priority and other defined classes don't get near their assigned...
View ArticleQuestion about MSDP
If I want to send my cache between MSDP peers, I think I need the 2 following command but they don't...
View ArticleVolume III Lab6 redistribution task
I think the SG doesn't take into account the fact that after the redistribution process, when we are asked to force the route to the 145.1.37.0 prefix via the external EIGRP route, if we don't change...
View ArticleNexus 5k FP
If you have two data centres connected via DWDM, could you use the nexus 5k platform and fabricpath across that link. Site A - Cisco UCS > Nexus 5k> DWDM ----------- DWDM------Nexus 5k----Cisco...
View ArticleProblems conecting an ASR1002 to a N5k thru a FEX
Hi There,I have an ASR1002 that I am trying to connect to a couple of n5k. the ASR1002 on port g0/0/0 connecting to a FEX and the FEX is on VPC with to 5k.The VPC is ok as it was connected an 7200 that...
View Articleccie home lab setup
Hi, I would like to create home lab with vmware esxi, gns3 or dynamibs for CCIE collaboration exam. is it possible and how? Regards
View Article