why have different IP numbering per rack number?
I don't really understand why vendors do this.surely its easier if all the racks use same IPs for scenarios , why bother adjusting on Rack number?
View Articlewhat to do after CCIE R&S?
This isn't directly related to the exam, but I was hoping I could get some general opinions here on what I should do assuming I pass (or don't).I'm working on R&S prep right now and am hoping to...
View ArticleDCrack3 with UCS addon
Hi All, Been practicing with UCS addon on rack mentioned above I wasn't able to see JBOD ports in 'show flogi database', it seems like they weren't logged in, although all interfaces were configured...
View ArticleCCIE V4-V5 Advice
Guys,As everybody know, v5 is coming and there is no seat avaiable anymore for v4. There are some thoughts that cisco is trying to put more seats for who want to try the v4. My question is, do you...
View ArticleNew study materials for the CCIE Collaboration
Hi all,Last week I tried to pass the voice lab and I failed, so obviously there's no choice but to try the collaboration lab. Does any one know when there'll be the necessary materials on INE (videos,...
View Articlegoing for ccie exam in 85 days
I have previously attempted ccie lab . Now going again i am planning to go through ine stuff and *** vod agian if any one intrested let me know
View ArticleCCIE R&S V5 - INE MATERIAL
Afternoon all,I am bored of hitting blog.ine.com for the announcement of the new CCIE R&S V5 material being released from INE! Impatience and excitement in equal amounts!!I am about to take the V4...
View ArticleRP in PIMv1/V2
Hi. are there any differences between PIMv1 and PIMv2 from the point of supporting Auto-RP/BSR methods? I mean can I use either of two methods in both PIMv1 and PIMv2 networks? tnx.
View Article6.2 ACL or MQC ?
Is there a reason to not use the existing MQC vs adding an ACL to the interface? SolutionGuide shows a new ACL being applied to the interface. This seems to be the SG tendancy for blocking...
View ArticleType 3 and Type 5 LSA's
Hi everyone,Just want to check whether my thinking is correct on this.A type 5 AS-external LSA originating in area 0 will not enter a stub area 1. A type 3 LSA, however, will be generated into area 1...
View ArticleBGP wrong AS
HI All, while was doing the CCIE RS Vol2 Lab2, keeping getting this wrong AS log in SW1 from BB#.Rack10SW1(config)#*Mar 1 00:55:47.935: %BGP-3-NOTIFICATION: received from neighbor 204.12.10.254 2/2...
View Articlefinal year project on voip
Hi all,I am doing BS in telecom and networks, i dont have much knowledge about VOIP but i want to make my final year project on Voip, kindly suggest me any good idea for my FYP, which should be...
View ArticleDoes SOO setup in BGP and EIGRP compromise redundancy ??
Guys,I have been reading articles about soo for both BGP and EIGRP.one thing that is not mentioned clearly is that if this solution creates another probolem when set up.here is the link about soo in...
View ArticleCisco UCS LAN Pin Groups
HI, am just wondering whether there is any use in configuring LAN PIN groups in UCS if you are not using disjoint layer-2?Let's say for example we have two LAN port channels coming northbound out of...
View ArticleClik here to view.
QoS - Traffic Policing on SVI - Catalyst 6509
hi everyone,Can I get some guidance on configuring Traffic Policing on VLAN Interface on Catalyst 6509 SUP2T?We have a lot of customers in our Data center. Each customer is located in 2 VLAN, one for...
View ArticleCCIEv5 topology
Hey guys - any ides when you will list/show the new INE topolgy for the v5?Reason for asking is i see most are going virtual for this and i might go the same way if Virl can run the INE lab.
View ArticleR&S LAB PUTTY
Hello all,I assume this question does not violate Cisco's non-disclosure policies.I know Cisco uses Putty in the R&S Lab, but is it a version that supprt Tabs?I failed my first attempt and...
View Articledebug ip routing lots of odd output
topology; AREA1-[SW1]----AREA0----[SW2]-AREA2here is an example below , i have two 3560 switches running ospf , both are in area 0 , and in SW2 , the debug ip routing is going crazy, below routes...
View ArticleClik here to view.
EvPC with FCoE
Hi, I've been testing EvPC with FCoE on INE racks, and would like some help in understanding something. I have my dual fexes connected no problem, and have my vlans and fcoe VLANs set correctly. I...
View Article