Clik here to view.
Routed psuedowire
hello to every one this is my first post in this forum i hope help me.i have 4 sites that are connected via ospf in backbone. all i to do in each site is to configure my gig0/1 an ip address and put it...
View Article6.2 DoS Prevention
I was unable to verify TCP INTERCEPT as stated in the SG. An earlier post suggested turning off CEF (but this is needed for MPLS). Ideas?
View ArticleEIGRP SOO
Hi,I am having hard time grasping SOO concept especially when it is set up on backdoor links. Exp: P1-------------P2 | | CE1 ---------CE21. P1 & P2...
View Article1.9 VTP Transparent (what if root bridge on the SW4 or SW3 or SW2?)
Need your help to clarify some of my doubt.Here's in Task 1.9, there is no any where in the question mentioned about root bridge, as the trunk is formed SW1-->SW2, SW1-->SW3 & SW1 -->SW4...
View ArticleMeaning of placing VPN Device Parallel to Firewall
Friends, I am not able to understand the deployement of VPN Device Parallel to Firewall. Does it mean:Q. VPN module is inside the firewall?Q. There is a separate VPN box outside the firewall?if its...
View ArticleHow to configure symmetrical load balancing with 2 links with single ISP
Hi Guys, I'm working in a LAB and I'm trying to configure symetrical load balancing with 2 MPLS links , same ISP.Basically, I have 2 routers that work as LAN routers and 2 Routers that work as the 2...
View Article8.1 Legacy Frame-Relay (placement of class)
I understand the correct numbers for this excercise, and how they were calculated. No problem here.But I do have a doubt about where I can put the class -- VC vs Interface. The SolutionGuide places...
View ArticleMulticast
In some examples, I have experenced that Multicast is working between two customers without enable 'address-family ipv4 mdt' in core..how does it work???
View ArticleIP SLA configuration
Hi Guys; i need some help configuring two way active management protocol on ME 3600x devices running 15.2.2 IOS. The details of this protocol are listed...
View ArticleNAT : Endpoint Agnostic Port Allocation
What is NAT Endpoint Agnostic Port Allocation? When would you use it and what problem does it solve?
View ArticleI'm looking for Study partner who is just started CCIE Voice. Only in USA...
Hi I'm looking for study partner who just started out doing the CCIE Voice.I don't want to slow you downI have my own lab so we can study using my lab or having you own lab is better
View ArticleGreat to be on board, but...
Hi all,Great to start studying for the CCIE R&S - Finally.I just brought the videos and workbook bundles. I'm working through Vol2 workbook using dynamips / gns3 and did ran into a few missing...
View ArticleMPLS 101 - Missing something
Hi all I am having a problem understanding an issue I have and in particular the verification of the issue. The setup I have is based on the INE R&S topology but I have constructed a diagram which...
View Article1.15 documentation error - solution has extra requirement
The question is:1.15 Layer 3 EtherChannel • Configure links Fa0/16 & Fa0/17 on SW4 and links Fa0/19 & Fa0/20 on SW2 to be bound together as a Layer 3 EtherChannel. • Use Port-Channel number 24...
View ArticleCisco Doc CD - Products and Technology
I have seen other postings talk about the use of the DOC DC but I wasn't very clear on the access. I know the search function is disabled but somewhere I thought I heard that the entirety of the CD...
View ArticleQOS query
Hi Team, Queueing strategy: weighted fair Output queue: 0/50/64/1820 (size/max total/threshold/drops) Conversations 0/2/256 (active/max active/max total) Reserved Conversations 0/0...
View ArticleMDS switch for lab practice..
I see on the blueprint that the 9222i is the switch to get for the lab. However its very expensive. Is there a switch someone can recommend me I can purchase off of ebay that will do all the normal...
View ArticleClik here to view.
cisco 2522 for INE Lab
hi allacording to INE CCIE Lab R&S, the frame-relay is cisco 2522 (BB2).I purchased the lab from ebay. but confused how to connect the routers to 2522.which interfaces IDs will be used to connect...
View ArticleINE GNS3 Topology w/config for CCIE R&S with Quad NIC
Hello Everyone, I have attached a link to my .net file along with all the initial configs I use for my base lab in my studies for CCIE R&S. I just thought someone else might be able to benefit from...
View Article