CCIE R&Sv5 GNS Home Lab
Dear Alli passed CCIE SP very recently.now i want to go for CCIE R&S Track can you please tell me how to setup home lab with using GNS3 software in order to test and practice all features from...
View Article15% off CCIE Collaboration ATC!
INE's CCIE Collaboration ATC and Network+ Video Course Download are available for 15% off when you use coupon code SELFPACED15 at checkout - limited time only! Your purchase also includes free access...
View ArticleReliable GRE backup interface lab
I'm going through the reliable backup int lab for GRE, which I see was updated 7/7. Here is what I'm getting caught up on. Configure IPv4 static routes on R5 for R4’s Loopback0 interface via both the...
View ArticleHSRP & VRRP state of router
Assume there are 3 routers sharing the same HSRP group. So one router will be in Active state, other router will be in standby state. What state the 3rd router will be in ??? Same question I would like...
View ArticleFSPF calcualtion and FC Portchannels
How does a FC portchannel effect the FSPF cost calculation? (if at all). would the cost be equal to all of links in the port channel? or will it be equal to all of the links in the port channel that...
View ArticleEIGRP Section DMVPN down on R5
I am going through the EIGRP section of the new V5 workbook and have got stuck at the first hurdle. All the network statements are on but between R2 and R5 DMVPN is not upR5#sh...
View ArticleClik here to view.
Redistributing static routes into OSPF
"% Only classful networks will be redistributed" Why?
View Article4.1 PE-CE Routing
Hi All, R6 has two links to BB1, s0/0/0 and s0/0/0.1. The Scenario and the WB only uses s0/0/0.1 to connect to BB1. What am I missing here? -- Thx David Sudjiman www.davidsudjiman.info
View ArticleHelp with VNIC Configuration for INE v5 Lab with CSR1000v
Hi guys,I am trying to build INE's v5 RS Lab with CSR1000vs but have limited knowledge of VMWARE. I have managed to procure a server that will easily run 20+ instances of the CSR1000v. I have 20...
View ArticleWhich STP derivative will not generate TCN BPDU except port fast ?
Which STP derivative will not generate TCN BPDU except port fast ?
View ArticleModifying OSPF route cost without IP Ospf cost command
Is it possible to modify the cost of an OSPF route without using the IP OSPF cost command? (Not referring to default route originated by stub commnd)
View ArticleClik here to view.
AToM not passing traffic even with vc up.
Dear Community member, I need you to assist to suggest possible reason for the following issues in the attached diagram. 1. IGP is OSPF2. mpls is enable across the network.3. reachability is confirm...
View ArticleEigrp metric calculation issue in named mode
Hi ,i just tried to calculate the metric for the prefixes in named mode with the new formula,after trying for many (from my point of view cisco document is not clear )times,i couldn't able to calculate...
View ArticleClik here to view.
Feasible successor question! (In the right forum this time..)
First off..you know you've had a long night of labs when you type "router eigrp 100" into the URL bar. Anyways, my question..On the lab ..EIGRP Traffic Engineering with MetricWe are tasked with...
View ArticleIKEv1 VPN High Availability with GRE over IPsec Task
Guys,maybe i missed something in the taks but how did R3 preferred to reach Sw1's Lo0 through R1?In the other task, IKEv1 VPN High Availability with Crypto Map and RRI task, R3 preferred to reach Sw1's...
View ArticleClik here to view.
FC/FCoE Question Regarding Fabric-A/Fabric-B Design
Hi guys! I'm currently studying some FC/FCoE designs and I woul like to double check some stuff with you... I read somewhere that you should not connect fabric-a and fabric-b togheter. Let me post a...
View Article4.12 MPLS L3 VPN and OSPF Domain-ID - help
I think for the most part, I understand this workbook lab.However, I am getting stumped on why the Loopback1 interfaces (redistributed into OSPF via connected) are chosing the backdoor link instead of...
View ArticleEXAM LAB Sessions
Hi everyone,Somtimes when doing labs from the Workbooks, I manage to resolve the issues with a different approach than the onein the solution provided in the lab itself. I'm wondering is this is valid...
View ArticleZBPF Asymmetric Routing
Anyone else have any trouble getting this lab functional? My redudancy between R1 and R2 seem to keep flapping from standby to init. I thought maybe it was my config so wiped both routers and started...
View Article