7.7 Dampening
I tried hard even looking in workbook1 (BGP), to understand the values in dampening.I would much appreciate it, if someone could explain to me the solution provided here: dampening 5 2000 1000 15?Thank...
View Article2610XM Flash Upgrade Failure
I've recently purchased three 32MB Flash SIMM's to upgrade my 2610XM routers and 2611XM router to 48MB total. When I take out the 16MB chip and put the 32MB chip in, the router goes into rommon. It...
View Article7.42 BGP Conditional Route Injection
Hi All, Could someone explain how setting the origin to igp in the inject maps of R4 and R6 fixes our routing loop issues? Thanks. - Kevin
View ArticleTask 1.3 Spanning Tree
SW2 is going to use the link to SW1 as root for instance 3, as SW1 is root for instance 3 so cost is less over directly connected trunk. The task says that you have to configure SW4 for this task. How...
View ArticleClik here to view.
IP Multicast Boundary IN/OUT
Hello,I was just reading these days some multicast and i noticed that something was not working as expected.The topology is as below with PIM-SM everywhere, R5's loopback 120.1.5.5 as RP. R6's Lo0...
View Article6.2 Reflexive acls
The SG's solution for 6.2 indicates that ALL hosts behind R2 need protected. The wording indicates that we need to protect VLAN 27 and NOTHING ELSE. Should we need to protect host on SW4 then the...
View ArticleAutomatic reply: RE: Traffic Redirection Question
I will be out of the office beginning 4/21/2014 returning on 4/22/2014.
View ArticleComments in TCL script
Does anyone know if you can put comments in a TCL script? I would like to do something like thisforeach address {#router11.1.1.1#router22.2.2.2#switch13.3.3.3} {ping $address{ I am building out some...
View ArticleAutomatic reply: RE: CCIE RSv5 Equipment Build
I will be out of the office beginning 4/21/2014 returning on 4/22/2014.
View ArticleCCIE ATC Sec videos about attacks
I'm currently watching some of the ATC 3.5 Sec videos. Brian has mentioned a few times "I'll show you more about the different attacks in a later video". Or "I'll show more about this topics in the...
View ArticleWhat console servers do you use?
I am in the market for a big console server.I use a Cisco 2511 very happily in my rack, but I need to connect to about 40 devices.Does anyone know what INE use in their racks as I am looking for a good...
View Articlehow to check the open ports on ASA and switches
Hi !,how to check the open ports on ASA as well as in switches like we do on routers [ show control-plane host open-ports ] Thanks
View ArticleAutomatic reply: What console servers do you use?
I will be out of the office beginning 4/21/2014 returning on 4/22/2014.
View ArticleProblems with Graded Troubleshooting Labs?
Has anyone had any problems with the Graded Labs today?I booked up all 3 troubleshooting labs and not one of them graded, it just hangs on the score report and never completes.I have logged a ticket...
View Articlet37 fax onramp/offramp
Hi all. first of all, I don't have any knowledge of voice, because I'm an RS guy. but I'm in the process of configuring the T.37 onramp/offramp and need some help. my config is works in onramp portion....
View ArticleHOW TO CONFIGURE SIP DELAYED OFFER?
Is there any command to force a Cisco SIP Voice Gateway (VG) router to use Delayed Offer. I am using IOS Version of 12.4(22)T on Cisco 2811 Hardware. The basic requirement is that to demonstrate that...
View Article2.2 Summarized routes back to RIP on BB3
Hello community,In this task, R4 learns 30.0.0.0/16 through 30.3.0.0/16 and 31.0.0.0/16 through 31.3.0.0/16 via RIP from BB3 and summarizes these into 30.0.0.0/14 and 31.0.0.0/14 into OSPF. Later in...
View ArticleDual-home site PE-CE routing
Hi Consider a dual-homed site, CE1----PE1---PE2---CE2 with the CE's connected via backdoor link and with RIP as the PE_CE routing protocol. Routes are advertised from PE to CE1 via redistribution....
View ArticleInterAS L3VPN- Back to Back VRF with OSPF
Hello experts,I am trying to configure InterAS L3VPN with Back to back VRF using ospf as the protocol between the 2 AS'es. Topology is very simple. Have an issue, plz let me knw if someone has seen it...
View ArticleASA QOS shape average limit
My understanding of the shape average <rate> command is to set the bucket that traffic resides in and is shaped out of. I've read that this should match the CIR that the ISP provides me, but the...
View Article