Is anybody preparing DC ccie?
Is anybody preparing DC ccie?I am going to take my lab somedays later. hope to communicate with people who are preparing DC Lab too.
View ArticleTask 5.3 Pim
Im finding the wording of this solution quite difficult to understand. "Configure the RPs so that only sources connected to R3 and R4 areallowed to send multicast traffic streams" From this I got "all...
View ArticleTask 5.2
Is an mroute allowed? is an mroute not the same as a static/default route and not allowed unless otherwise stated?Why does the SG use an added ip address on tunnel 14? again this shouldnt be allowed?
View ArticleTask 8.3
On task 8.3 it says packets marked with a precedence of 3 limited to 1Mbps, normal burst 1500bytes, but doesnt say anything about maximum burst size. Where did they get 2000 from? on the lab exam would...
View ArticleGlobal ACL question
Dears,I was checking the solution of the task "ASA basic access-list" and i was confused about the following:When we apply a global ACL on the ASA and there are no ACLs applied on interfaces, the...
View Articlethe idea of MPLS ? how and why ?
hi allI am still new to MPLS, I like to know the reason of the technology I read before going into the details.As I understand, the idea of MPLS is to forward the traffic based on Labels not IP...
View ArticleIne CCIE SP Labs in dynamips with i5 processor????
Anyone has successfully done running ine ccie SP Labs in dynamips with i5 processor ????
View ArticleAutomatic reply: the idea of MPLS ? how and why ?
I will be out of the office the week of April 14th, returning April 21st, with limited to no access to email. If you need immediate assistance please contact Cliff Wilberding (601.297.6642 or...
View ArticleClik here to view.
Michael Marx, CCIE #42713 (R/S)
My apologies for the length, but I have imagined writing this post for about a year now. I am sure it littered with typos - but now its too long to proof... Frequently while I was studying I would...
View ArticleIOS + MPLS
I was trying to set up and MPLS lab in my real lab when I've got stuck on MPLS.It seems my router doesnt support MPLS R4#show verCisco IOS Software, C2600 Software (C2600-ADVENTERPRISEK9-M), Version...
View Articlewhat is the difference between snmp,netflow and rmon?
can any one explain to me the diff between those guys?
View ArticleAutomatic reply: what is the difference between snmp,netflow and rmon?
Dear sender, I am out of office untill 18/04 , for queries related to Tunisiana account you can contact Zied sassi (29535331) or Jrad mohamed ( 24699094) , for queries related to Orange account...
View ArticleiSCSI Dynamic Initiators
Hi,Can someone enlighten me on how to assign VSAN (other than VSAN 1) to iSCSI initiators, other than under vsan database where you would assign the whole iscsi interface, i.e;vsan database vsan 10...
View ArticleClik here to view.
INE LAB FCOE
I am completing the FCOE lab on INE datacenter workbook. I have configured the devices as per the workbook.When i log into the EMulex server i see the PWWN as the target mapping but when i go to...
View Article6.2 ZFW
I see in the ZFW config under class-default they used "pass" on the inside and outside zones. Do you think it would be count if I matched everything to an inspect? Also I did nbar match protocol snmp...
View Articlewhere is the neighbors? (show ip bgp summary)
Hi,I have completed 14.1 to 14.7.There were some problems, eg. task 14.6 PE-CE Routing with RIP which I think messed some of my other solutions up, since I dont know if I did it correct; bottom-line it...
View ArticleDid Mark snow create a study plan for the CCIE DC track?
Did Mark snow create a study plan for the CCIE DC track? I followed his plan for the CCIE R&S and i passed it on the first attempt not only that, I finished the config section within 3 hours and...
View Article14.8 OSPF Sham-Link
Hi,I have almost completed this task, but I have a strange error, which I can't find.I configuered everything, but my sham link is not coming up. On R6 I can see...
View Article6.4 ICMP Filtering
There's one entry in ACL TO_SW1 to permit ping from R6 to 228.28.28.28, which is permit icmp any host 228.28.28.28 echo.Shouldn't it be like permit icmp any host 228.28.28.28?
View Article