Full Scale CCIE DC labs
When is INE Going to release full scale DC labs. Nobody is Providing any tentetative schedule for full scale labs release.At least for CCIE Security INE is saying that they will start releasing Full...
View ArticleBGP down due to RT change
Hi Friends, We are using EBGP as PE-CE routing protocol.When I added a new import RT in to the VRF, the CE-PE protocols was down and came up automatically.Is it a desired behaviour and how can we...
View ArticleNotes From Failure #1 or "My $1500 Water Bottle"
On November 25th, I made my first attempt of the CCIE and failed it. I've always found insight from reading other people's lab attempt stories so I wanted to share my notes. I've always enjoyed...
View ArticleAdventures in IP Default-network
here goes>>> BB3 is connected to R6 over a serial link with the network 54.1.1.0/24 between themthe setup below..the actual question the very bottomrouter 6Rack1R6(config)#ip default-network...
View ArticleMDS--UCS Portchannel
HI, Wasted around 4 hrs in figuring it out why my link is still no UP below is output LinkUCS--(11,12)--MDS1 (1,2) need some suggestion as this really frustrating !! simple damm link is not coming up...
View Article14.11 alternative
From what I can see, there are two options here - allowas-in / as-override.If config is required on PE - choice is allowas-inIf config is required on CE - choice is as-overrideOn R5 I set allowas-inOn...
View ArticlePolicy Map only matching on the first entry?
Either I am missing something or my config is wrong or it just works that way?I am working on a 3750 switch and trying to police some traffic outbound. There are servers connected downstream of two...
View ArticleVendor Independant Voice Books
Hi,Is there any vendor independant books that are recommended for voice? On INE recommended reading, they only suggest Cisco propreitary books, but a lot of companys use different vendors.
View Article14.12 - Explanation is weak
The SG is really strange for this task.•Configure a “backdoor” BGP peering session between SW1 and SW2 using the inter-switch link configured previously.•Ensure that this configuration does not result...
View Article3rd strike, I am out
So I sat on the exam few days ago for 3rd time and failed again. This time I failed both the TS and the configuration, the latter by a huge margin. Let me start with the TS - after one hour and 20...
View ArticleOTV and encryption??
Not an OTV expert and had a quick question I hope someone can answer so I don't waste my time. "Not an expert" is putting it mildly. Bottom line is I was put on a project at last minute and given a...
View Article3.7 Policy Routing
Hi All, I can't figure out why I keep getting unreachable messages when I try to ping R3's loopback from R4. R1interface FastEthernet0/0 ip address 155.9.146.1 255.255.255.0 ip policy route-map...
View ArticleFailed attempt, need TS advice please
Hello OC,I failed my 2nd attempt. And while I kinda know what I could improve on the configuration section, I'm very lost about the troubleshooting score.10 tickets. Wrote the numbers 1-10, started...
View ArticleVDC on a stick
Hello All,When listening to the OTV related Video from the Nexus Switching course, Brian was explaining about VDC on a stick. I could not understand what it means. Can someone please explain about...
View Articleback to back frame-relay
HiIt is possible create b2b fr link in which:> keepalive must be on, and inverse-arp must be off
View ArticleTask 1.1 vtp pruning
Hi All,Above task 'Manually configure your network to behave as though vtp pruning has been enabled'. I came across a task like this in an earlier lab and was slightly confused by the answer and...
View ArticleClik here to view.
Multicast: Auto RP not Working
Hello community,For some reason I can't get SW2 to hear advertisements from the mapping agent (R1) or learn RP info. I also configured it to be a candidate RP and the maping agent is not getting its...
View ArticleImproving Knowledge in Cisco Hardware product
Hi All, I have recently completed my CCIE. I am planning to improve my skills in design area. I need your help.=> How we can improve our knowledge in cisco products?=> Any website from which we...
View ArticleLab topology for 642-661 BGP Exam Course (Keith Barker)
Hello everyone, Please excuse me if this is not the right place to ask such question - I am a bit lost here becasue there are some many topics here. Please move this to the right topic if necessary. My...
View ArticleEIGRPv6 not available
Hi all, I've got a weird situation or hopefully something simple I'm just not educated on yet. I am following INE's program, workbooks and equipment to study for my lab. I have a Cisco 2610XM with...
View Article