LDP labels for IPv6 prefixes
Does LDP assign labels for the IPV6 addresses too? Imagine if we only have a IPv6 ony core and we try to exchange vpnv6 addresses. the vpn labels will be assigned by BGP, but where will the transport...
View Article10.23 MQC Class-Based GTS and CBWFQ
class-map match protocol http vs class-map match access-group name WHY_USE_EXTENDED_ACL_TO_MATCH_ANY_HTTP_TRAFFIC There is not an explicit requirement for where http traffic is originating from. Are...
View Article14.13 - Issue
Checking through I can see that CE1 (SW1) does indeed get the default route, injected via R6 (PE):SW1#sh ip route | in 0.0.0.0Gateway of last resort is 155.1.67.6 to network 0.0.0.0B* 0.0.0.0/0...
View ArticleTS - General way to fix an issue
Hi all, DUring some labs, I always got the feeling that I fix the issue, but in fact not in the way it was expected...I have two examples here, and I would like to know how it is expected to fix them :...
View ArticleINE Expanded Checklist v5
Dear friends,can you please provide me expanded checklist for v5 since cisco checklist is looks very weired and complex. thanks.
View ArticleCCIE home lab setup
So i am just starting my CCIE R&S journey and I am looking for advice on how to setup a home lab. What would be the best way to proceed?
View ArticleQOS MUTATION MAP
I'm having trouble to understand the calculation and formula behind the mutation map...for example...Configure SW4 so that R1 sees packets marked at R4 with DSCP values CS0, AF31, and CS5 as DSCP...
View ArticleTask 6.2 Alternate solution
So I have circled back to lab 1 to go through 1-10 pre lab & hopefully I am now spotting better ways to do things. What do you good people think to this:Q)To help prevent this type of attack in the...
View Articlewhat is latest Terminal software used by RTP
Hi Team,Is RTP CCIE lab is using Secure CRT or Putty ? and appreciate providing the info. who did recently in RTP ,also can we use tab and ? to finding command or needs to type full command ?Thanks, Selva
View Article5.1 multicast testing
Hi everyone,I used 2 other way regarding this task and both seem work.1rst method : R2 (ser 0/0/0):ip pim nbma-mode (even if it's not recommended for dense mode, I was able to ping after that).2nd...
View ArticleMDS9222i Bandwidth Configuration
Hi Folks, just thought I'd share with you some b/w config for MDS9222i port-groups.We know we have 12.8Gbps of b/w available per port-group, and we are also told that when we use all 12Gbps for...
View ArticleIOS versions for routers and switches
Hello,I am trying to implement the CCIE Voice rack rental diagram v3 on GNS3. I am a debutant and I was wondering if the following IOS images for my routers and switches could...
View Articletask 4.3 volume II lab 12
i had the idea for this task to activate mpls only on the serial link between R5 and R4. That was interesting because at the end of the task although i was able to see the loopback of VPNA in SW4 i...
View ArticleWhy is Lab 3 4.1 Updated incorrectly with change in requirements but original...
Hoping someone from INE can help with this. Notice below the original INE scenario from Lab 3 3.1 verses the New via the Web. Notice the answer key is correct for the OLD version. Also the...
View ArticleSupermemo Study Method
I have a question regarding the best study techniques for retaining informationI read through this very informative blog post below about using Supermemo method of reviewing information at a certain...
View ArticleLab 3 Ticket 5
I am missing something on this lab. The solution guide has local-proxy-arp set as follows.R4:interface FastEthernet 0/0ip local-proxy-arpI did not make any modifications on R4 and had reachability. I...
View Article4.16 - "Configure R6 to advertise a default route only to R1 via RIP"
Task states to "Configure R6 to advertise a default route only to R1 via RIP" -- r6 advertises the default route on vlan 146, which includes R4.It seems like this is violating the constraints on the...
View ArticleEncrypted VPLS
if you have a dark fiber connection with 2 attached routers you own connected to a pair of switches on both sides and wanted to extend a number of VLANs using IPsec encryption is VPLS an option? How...
View Article7.13 BGP over GRE
I'm sure I'm missing something relatively simple, but for the peering between R2 and R4, why can't we peer (or why can't I get them to peer? over the FR cloud? Using 155.x.0.2 and 155.x.0.4 as the...
View ArticleImproving Knowledge in Cisco Hardware product
Hi All, I have recently completed my CCIE. I am planning to improve my skills in design area. I need your help.=> How we can improve our knowledge in cisco products?=> Any website from which we...
View Article