CCIE R&S LAB v4 still valid?
Hi all,I passed CCIE R&S v4 written exam on 3, July 2014.Is still possible to take v4 lab exam or from 4, July 2014 Cisco offers only v5 lab format? This is from Cisco Certification Support site...
View ArticleMST txholdcount
Does anybody know what the txholdcount means? Root this switch for the CISTOperational hello time 2 , forward delay 15, max age 20, txholdcount 6Configured hello time 2 , forward delay...
View ArticleImpossible IPSec VPN Task
Hi,I know this is a bit off topic as it's more a security topic, but the principle is the same - its just a site-to-site ipsec tunnel.Anyway, I've been given an impossible ipsec vpn task by my manager...
View ArticleWSA access issue
Anyone have successfully logged into the WSA?I'm trying to do the WSA initialization lab but can't get into the WSA.I can log in through the console but HTTP 8080 does not work. The WSA loaded with...
View Articlecrypto isakmp command error? CSR1000v image?
Hi,I am using image csr1000v-universalk9.03.12.00.S.154-2.S-std.ovaCisco IOS XE Software, Version 03.12.00.S - Standard Support ReleaseCisco IOS Software, CSR1000V Software...
View ArticleIOS NVI NAT
Dears,when using NVI NAT on cisco routers instead of regular NAT, can you please advise what is the difference between the below two commands:ip nat source static 1.1.1.1 2.2.2.2ip nat source static...
View ArticleNHRP redirect failed to initialise
Hello, I am doing some lab these days on DMVPN as i am preparing the RS v5 lab. I got this issu with GNS3 7200 router and latest IOS image c7200-adventerprisek9-mz.152-4.S5.bin.When I try to configure...
View ArticleASDM - monitor access only
Hi,I'm working now with WB section 'ASA local authentication' and I have one problem with ASDM read-only access. I checked documentation and I found: "The nas-prompt keyword allows access to the CLI...
View ArticleBGP AS-PATH list
Hi All,When I am looking in to the CCIE R&S V5 advanced technology lab "BGP Regular Expressions" I can able to see some routes are originating from AS 60 but AS60 is not configured anywhere. Can...
View Articleccie DC lab exam seat
Hiif any one interested to opt for ccie DC lab exam seat on July 9 Dubai location kindly let me know thanks
View Articlevtp transparent mode question
hi allin this simple topologySW1 ----------- SW2 ------------ SW3 SW1 = VTP server, SW2 and SW3 = VTP clientSW3 = STP root for all Vlanseverything was working fine, I changed SW2 to be in transparent...
View ArticleDDNS Configuration & Troubleshooting
G'day Everyone,I am kind of struggling here and really don't know where to turn to next and I was hoping if I threw my question amongst all you Cisco guru's you might be able to point me in the right...
View ArticleTask 4.13 Multi-VRF CE (VRF Lite)
When ever I try to configure for this task I always get the message that no router-id for ospf process 100...I don't know what to do with that ??? Although I copies and paste the initial config and...
View ArticleInitial config for a particular task
I am trying to do task 4.13 could not get it done...can anyone guide me that should I upload initial config of only that task and do as it is in the workbook as I did this also but still not getting...
View Article1000V Control Interface Port-Profile
So I've migrated everything (VMKs and VMs) to the 1000V with one exception - the Control interface on the VSM. When I attempt to migrate the interface to a 'standard' Veth PP, my VSM loses connectivity...
View ArticleAnnoying Difficulty Lab 4, 4.1
When I enable labeled unicast for R3 on XR1, I don't receive prefixes from R3 even with route-policy applied neighbor 10.0.193.3 remote-as 2000 address-family ipv4 labeled-unicast...
View Articlebgp redist internal lab
I dont think this lab is correct. That is to say, I didn't need to redist internal on R3 in order to have full reachability to AS54 subnets from AS100 devices.
View ArticleRestricting access to your ESXi Virtual Rack
I have built a virtual rack using an ESXi server and now want to enable a few co-workers to use it. What options do I have to be able to allow one co-worker to access the rack at once?Currently I just...
View Articlebgp gre
I did this differently to the SG (but with same outcome)I created a gre tunnel and advertised the tunnel endpoints into the IGP. Then I created the r7/r8 ebgp peering over the tunnel directly....
View ArticlePPP, PPPoE and PPP authentication
Hello, I'm wondering why the PPP sections are missing from the workbook? The topics are still listed in the blueprint.Thanks.
View Article