TASK 2.1
Task 2.1 states only that we should use authentication Type=1 (So clear text) but it doesn't specify a key, and by the default this works...it's simply the same as Type=0 AuthIf we look at Type=2 auth...
View ArticleTask 2.1 (RIP) Incorrect Suggested Solution
As an FYI, the suggested solution to Task 2.1 (RIP) is incorrect. On R4, we are required to advertise the most specific summary for the networks covered by the 163.1.0.0/16 amd 150.1.0.0/16 classfull...
View ArticleTask 2.1 - Where does the password CISCO come from?
Guys,SG uses password CISCO for OSPF authentication? Do you know where it comes from? Or it's just arbitrarily chosen?
View ArticleEAP-TLS
Hi all I am trying to get to the bottom of EAP-TLS, specifically step by step process explained here...
View ArticleTask 2.2
The SG announces VLAN 7 into ospf with a network statement. According to the diagramm VLAN 7 is not in ospf. Therefor I redistributed it with a route-map and redistributed connected. I think the SG is...
View Articletask 2.5 Load Distribution
Hi everyone,For this task, I changed the EIGRP metric weights so to only take Delay into account in the metric calculation. Makes the maths easier.Is that valid? I saw no specific instructions...
View Articlentp multicast - only ttl of 1
I tried some ntp multicast today but I did not have much luck with what looks pretty straightforward. ntp master 5interface f0/0 ntp multicast 230.0.0.1 ttl 32 For some reason the packets generated to...
View ArticleBGP update group teaser question
Before reading I know the answer to this question after a bit of research - but I would like to open this up as a teaser to who else gets the right answer :-)I am using the INE volume I topology - IGP...
View ArticleCCIE RnS Version Change to 5 by 2013 End ?? Any Information
hello everyone , I just wanna know about the version change of RnS track ??When Cisco will announce & when its gonna change ver 5 ( new bluepint ) What New things are expected to get changed . If...
View ArticleIOS-XR_ASR9k_H-VPLS_with_MPLS_Access_Split_Horizon_Issue !
Dear All I am working on a requirement to create a H-VPLS Setup with MPLS Access but am unable to get the setup working as the NPE is not able to send traffic received from other NPEs to the MPLS...
View ArticleASA GUI vs CLI Usage in Exam
It is my understanding that the ASA GUI is now available for use in the exam so I have to ask to what extent is the use available in terms of configuration? Could it be safe to assume that even though...
View ArticleTLV in EIGRP
I know TLV stands for Time, Length and Value. I also understand that:The Version field in EIGRP packet headers is actually a protocol discriminator: a value of 1 would mean IGRP, the value 2 means...
View Articleshow running config
Hi there, quick question. What is the command to get the output of "show runn" without the '--More--' entries ?I usually set term len to 0, but I think there maybe a quicker way?Many thanksDominic
View ArticleSouthbound ports/Server facing ports of 2104XP IOM
Hi all, In UCS course, which is said by Mark , 2104XP has got only 8 10G southbound ports towards blades, however, in the same video (Hardware Options) the cisco website he shows said 2104XP has got 16...
View ArticleClik here to view.
Regarding IP comunicator
Hi everyone, I am using Cisco IPC to to get registered with my CUCM 8.6 , but my IPC not registered and its showing Blurred screen(its not allowing to change TFTP and ADapter settings)...
View ArticleClik here to view.
in which case, you can only get a few of reply when ping is used to test...
Rack1R1#pingProtocol : Target IP address: 225.25.25.25Repeat count [1]: 100Datagram size [100]: Timeout in seconds [2]: Extended commands : yInterface [All]: serial1/0.1Time to live [255]: Source...
View ArticleIP Routing Lab Issue
Hello I'm working with the Ip routing Section for the lab 3.1 I have a doubt, the R1,R4,R6 for the ethernet connnection there are in the VLAN 146, but I'm not able to ping R4 from R1 and R6 but I can...
View Article4.2 VPN Tunneling
Hi,In theory, when the task says "You are allowed to create additional interfaces to accomplish this task", it should also mention that we are also allowed to create NEW ip addresses and that we are...
View Article(Remote Rack) Phones
Guys,I recently started using INE racks and a bit confused about the (Remote Rack) Phones:aka - "Branch1 Phone 2 (Remote Rack)" and "CorpHQ Phone 3 (Remote Rack)"I cannot find or register them at...
View ArticleCisco Metro-e Books/Docs/Training
Hi Folks,I really have no idea what the best forum for this is, but since metro-e is, for the most part, SP tech, I figured folks here might know (it doesn't appear to be covered at all in the SP ATC...
View Article