SIP Supplementary Service Update CID Message
I'm implementing CUBE, but because I have to send specific ANI's to specific Service Provider SBC's, I'm using "steering codes" prefixed at the beginning of the number to route the call correctly....
View Article[Success ] CCIE RS written
Hello Community,Just to let you know that I pass written R&S with 916/1000.Next step, first attemp Lab due to December.Thanks to INE and everyone on this community for helping me acheive my...
View Article5.9 Inter-Area MPLS TE with OSPF
Hi, Is inter-area MPLS TE with OPSF/ISIS is supported on dynamips? because here i have apply config but in the end tunnel not showing up/up. Verified all the configs are upto mark.R1#sh int des | in...
View Article[IPv6]- stange behaviour
Hi community,For now I use the ASET Lab of cisco and I see a stange behaviour for IPv6.Each time I reload the routers I see that their link-local IPv6 and EUI-64 adresses have changed and so my OSPFv3...
View ArticleCCIE DC Written ?
Folks, I have not noticed on Cisco's Learning Network that they have specified which generation UCS Blade Servers are being tested on the written exam. I do see that they LAB exam is based on M2...
View ArticleMPLS L3VPN over MPLS TE
Hi all,I have a problem in L3VPN over MPLS TE between PE (OS XR) and PE (IOS) in any INE SP labs. I made a Te between PE ( OS XR)--PE(IOS) routers with autoroute anouce. On OS XR, the lable status to...
View ArticleHow to extend pod bookings?
Hey Guys, Is there away to extending the booking of the pods while your doing the troublshooting lab? When I was doing the troubleshooting lab, there were free spots availble on the scheduling page...
View ArticleProblem with GNS3 + USB to Ethernet setup. Please help.
Hi,I'm new to the forum, just started the CCIE journey. Have 2x3560's, 2x3550's, the routers are virutal (GNS3). Now, in GNS3 I connect the clouds to my usb-to-ethernet adapters which are in turn...
View ArticleTroubleshooting a VPNv4 peering (no IPv4 address-family)
HI All I would like some recommendation on debugging BGP adjacencies for VPNv4 specifically where the IPv4 address-family is not active. I have the following debugs configured but I am seeing no...
View ArticleClik here to view.
ip sla and object track
how i can configure ip sla and track to ping loopback in other networke and if 20%packet send or recive to loppback 0 drop object track is down?
View Article7.35 BGP Aggregation - Attribute-Map
By default so far following all the add/remove configs in the BGP SG, R6's bestpath for 112.0.0.0/8 isn't via R1/R4, it's via it's external peer to BB1. Therefore the no-export community doesn't...
View Article7.2 establishing ebgp peering
hiin the result of show ip bgp in R1 we see he receive the same route from BB1 and BB3 and one we be preferredmy issue is I need the correct config of BB3 and BB1interface Loopback0ip address...
View ArticleUpgrading my lab/getting ready for the CCIE
Hey,So i'm starting to upgrade my lab and i was hopping to get suggestions on what to buy or rather what would be a better buy:So as of writing this i have:1x 2511-RJ (access server)1x 2611XM w/ nm-8as...
View ArticleCUE jtapi integration
Hi all, Need a clarification or tip about the way in the Lab , if possible, evaluate solutions.Question was to integrate CUE with CUCM. That's ok. I created a jtapi app user for the integration, made...
View ArticleCCIE LAB Points on Lab Exam
Hi all, I'm going to take my labe exam on end of july.I'm not sure if it's the right place to ask.In the lab guide during the exam is there a point indication question by question or by topic or the...
View Articleip igmp join-group vs ip igmp static-group
I've come accross an issue that I'm having a difficult time understanding. I have 2 devices, lets call them R20 and R21, connected via ethernet. OSPF adj between them, pim adj between them, igmp...
View ArticleCCIE SEC v4 workbook
Hellonoticed new CCIE Sec V4 technology labs available on member page - great resource.Would like to know when is ETA for v4 workbook?Thanks
View ArticleBGP RIB Failure
I know this is probably an oversimplified question, but is having a RIB failure in your BGP table inherently "bad," or is it just something to take note of. Meaning, if you see a r> on a route,...
View ArticleCustomer Implementation Engineering - Raleigh NC
Normal 0 false false false EN-US JA X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes;...
View Article