Quantcast
Channel: IEOC - INE's Online Community
Browsing all 10744 articles
Browse latest View live

set ip default next hop vs set ip next-hop

hi,i couldn't figure out what is the diffrence beteen the two?set ip default next hop vs. set ip next-hop 

View Article


CME Phone calling CUCM phones

Hello AllI am trying to call from a phone registered with the CME to a phone registered with the CUCM--I could not make the call.  However other direction it works (CUCM-->CME over the SIP...

View Article


Layer 2 EtherChannel with PAgP

HiI was doing lab on RS5 Layer 2 EtherChannel with PAgP and in the workbook it says configure the po12,13,14 with switchport trunk encapsulation dot1q and switchport mode dynamic desirable and other...

View Article

Question on Task 4.8

I tackled this task by applying tag to routes being redistributed into OSPF (routemap RIP2OSPF) on R4, and I filtered out the tagged routes on R5 as I redistributed OSPF2RIP and I did the same on R5,...

View Article

save and load config on WLC,ISE ,WSA

Does anybody know how to save and load  configuration manually on WLC,ISE,WSA so  the next time I rent the rack i could load the config on them ? do I need run FTP on my computer and import or export...

View Article


IOS NAT Overload with Pool

I am wondering what the behavior is of NAT when you specify the overload keyword when you have also specified a pool with multiple addresses. Does it just use the first address till it runs out of port...

View Article

Building INE's RSv5 topology with physical switches

Use this thread for discussion on building INE's CCIE RSv5 topology using physical switches.Details of INE's RSv5 topology can be found here.Details on LAN Access Switches can be found here.This thread...

View Article

OSPF virtual-link

Hi Friends, I have the below network design. AREA0 ----AREA1----AREA2----AREA3 Inorder to make the connectivity from AREA2 to AREA 0 I can create a virtual-link with AREA1 as a transit area. How can I...

View Article


CCIE R&S v5 ATC - EIGRP Traffic Engineering with Summarization - Q&A section

Hi community,At the end of the EIGRP Traffic Engineering with Summarization ATC, we had a good question in the Q&A dedicated section. Specifically this was : "Can we increase the metric of the...

View Article


ZBPF Asymmetric Routing

Anyone else have any trouble getting this lab functional? My redudancy between R1 and R2 seem to keep flapping from standby to init. I thought maybe it was my config so wiped both routers and started...

View Article

EIGRP MULTICAST ?

Hi,I've noticed that EIGRP named mode has "ipv4 unicast" and "ipv4 multicast".What do is the multicast for ? is it meant to replace PIM ?how do I implement it ?will we learn about this feature ?

View Article

Image may be NSFW.
Clik here to view.

RIPv2 Filtering with Extended Access-Lists

The solution for this task doesn't fulfil the requirement as accurately as most of the technology labs. The tasks says that "routes for VLAN 7 and VLAN 9 are accepted only from R1" whereas the solution...

View Article

Automate Loading of Advanced Tech labs

So each lab in each section now has its own config to be loaded. Its getting very time consuming to blow back to a base config on all 10 devices and then load the needed configs. Here is what I do now....

View Article


R&S Vol-II v4 - Forum section missing

Hi,Since yesterday I have noticed that the 'INE Products' Forum section is missing 'R&S Vol-II v4' completely. I had a question i wanted to put out to the Forum, but there is no place to ask the...

View Article

Inter-AS MPLS Option 2 - VPNv4 exchange

Just going over Brian's ATC video for this,  I am confused about one part of it.   when we are peering between the Service providers using ebgp vpnv4... say ... R1 ( AS1) ------ XR1 (AS2) the IOS...

View Article


Wireshark on Win7x64 vmware VM - can't see tagged frames?

Hi,I've been working on building up my lab in the format of ESXi host with the 20 CSR1000V routers and 4 physical switches.I installed a copy of Win7x64 as a VM and gave it a management NIC and a Lab...

View Article

Task 2.3 layer 3 interfaces

the task contains 4 point . each point talking about number of commands but as i read it . no point talk about configuring sw4 to vlan 67the last set of commans configure sw4  sw4:interface...

View Article


Should I see the CSR1000V's as CDP neighbors?

Hi,If I setup two CSR1000Vs on VMware and give each router a dot1q sub-interface of say vlan 100 - should they see each other as CDP neighbors?  Does the VMware vSwitch work more like a real switch or...

View Article

Cisco 6807 Switch Information

Hello everyone,Does anyone know what is the port density & throughput of cisco 6807XL modular switch?

View Article

TASK 3.1 - IP Address Error on Diagram

Hi, just to point out, that in the diagram connection between R6 and BB1 shows 54.x.4.0/24 and it should be 54.x.1.0/24.Refer to BB routers initial configs. you should see 54.1.1.254 for DLC101.  This...

View Article
Browsing all 10744 articles
Browse latest View live