IP address allocation for service profile
Hi everyone, I know the reason why we would need an ip address for a blade from mgmt ip pool, however, is there any particular reason why we would need that for a service profile ?Mark said it is...
View Article2.11
Not sure I understand the solution and the issue on this. How does settign my Admin distance for local BGP routes resolve this. Hoping to understand this. ( I could nto figure this one out had to...
View ArticleMAC Register Mode in Network Control Policy
Hi all, As we know there are two options we could choose for mac register mode, which are only native vlan and all host vlans.For my understanding, if we are running a hypervisor on the blade and want...
View ArticleCUCM tar files
Where can we download the cucm tar file, alos the final configuration files for the 10 day bootcamp
View ArticleRelease of CCIE Security V4 Materials
Hi,Just wondering if INE have any plans for the release of the new CCIE Security blueprint materials any target date?
View ArticlePIM-1-INVALID_RP_REG
Good Morning all Im working (slowly) through the muticast section in Vol1Im trying to configure sparse-dense mode, but one of the routers cannot register with the RP.The RP returns the...
View ArticleBurst(bytes) and Rate(kbps) of Qos policy in UCSM
Hi everyone, I would ike to create a new Qos policy for a vnic in ucsm, and I have got Burst and Rate need to be specify, would you please tell me what Burst and Rate is in this field specifically?...
View ArticleME3400 Output Shaper dropping packets
Hi Folks,I have run into an issue on our Metro-Ethernet SP network which is described as follows:Device - ME34001. Inbound policer on fa0/1 (connected to customer equipment) set at 9.5 Mb/s - Tc 250 ms...
View Article10.26 MQC Two-Rate Three-Color Policer
<!-- @page { margin: 0.79in } P { margin-bottom: 0.08in } -->Hi All,I am trying to understand one thing regarding this task.Per task Modify the first-level policy-map applied directly to R4’s...
View ArticleAbout IPv6?
i have 4 computers conneced via switchi give IPv6 address (link-local address) to all computersif computer1 wants to send data to computer2 How computer1 knows the mac address of computer2?i know that...
View ArticleMulticast and IPSEC question
Can someone please explain why multicast/broadcast packets cannot be carried over an IPSEC tunnel? I can understand that it cannot be done in Transport mode, but what about Tunnel mode?
View Article11.4 Traffic Filtering using tandard Access-lists
I am not understanding how this was solved using access-list 1 permit 150.10.0.0 0.0.6.255access-list 1 permit 150.10.0.0 0.0.255.255 1. not sure how 0.0.6.255 matches wat I need it to match and B why...
View Articlemistake in 1.48
there's a mistake in the above question because between the question and the solution have changes in hostnames that routers should use to authenticate in CHAP mode. I solved it but i've noted that...
View ArticleBGP inject-map
Hi All Is there any way to make BGP inject-map work with a connected interface, i.e. advertise more specific routes from that range or is it completly reliant on a dynamically learnt route from a...
View Article13.37 TCP Optimization - high performance TCP options?
Guys,Task requires us to: - Avoid the TCP "silly window syndrome"- enable high-performance TCP options- Set the TCP window size to twice the standard 16 bit maximum value- Limit the wait time for a TCP...
View ArticleOrder of Operations - R&S Workbook
Do you have to perform the configurations in the exact order in the R&S workbooks for the solution to be successful?Do you normally clear the config and start fresh for a new section in the workbook?
View ArticleTroubleshooting Questions
Hello all,I have went through a few troubleshooting labs from WB4 and have noticed several typo's and solutions that dont actually work. I'm pretty frustrated by this WB and it is by far my least...
View Article[mpls vpn eigrp pe-ce]
hi, all: if you have an mpls vpn setup, with 2 or more CEs using EIGRP you're only required to redistribute BGP into EIGRP without having to set a metric for the CE to receive the routing table. This...
View ArticleClik here to view.
BGP aggregate and OSPF area 0
I am doing a re-design on a portion of our network and have hit a stumbling block with regards to BGP aggregate and OSPF area 0 Reference the diagram below, the current setup is all traffic between the...
View Article