spanning-tree portfast on interface enabled [do you agree?]
- spanning-tree portfast on interface enabledportfast--->immiedietely jump from blocking to forwarding state [omnit listening and learning]portfast--->don't block bpdu...
View Article[BGP]Update source and tcp server ?
Hi guys, I understood The usage of update-source command,but when i labed up a few things this is what i found outi)specifying update-source loop-back on one side is enough to from the peeringii)also...
View ArticleTask 5.3
I used for this task a different approach than the SG. I filtered the traffic with an extended ACL:ip access-list extended DROP_TTL_LESS_13 deny ip any 224.0.0.0 15.255.255.255 ttl lt 13 permit ip...
View ArticleINE CCIE v4 workbooks initial config
hi allI have INE CCIE rack in home, my question is about the initial config of the devices (not the backbone) for troubleshooting labs.because when you use INE rack rental you can load the configs !!...
View ArticleSCRACK4 ASA1 & ASA2 licenses are not the same
The active/standby configuration will not come up due to a license mismatch
View ArticleTask 2.8 Workbook II lab 18
I don't know if in the lab would be allowed but in this task i have bound a static default route to null0 interface on R5.That caused the advertising of an internal EIGRP default route without the use...
View ArticleASA 9.0 DMZ configuration question
hi everyone,this is the first ASA that I configure with the new 9.x (or 8.4 and above) version. I manage to get the DMZ to work, but i don't like my config at all. I will high-light what I struggle...
View ArticleINE ATC IPS Video
Study partner just told me that the INE IPS video is still based on the IPS 6.x operating system and not the new 7.x operating system as per the CCIE Security v4 blueprint.I know there is not a lot of...
View ArticleHow to prepare for ccna exam
Although i know that there is no shortcuts for this exam but do you guys recommend to buy cisco routers at home to practice? Do i have to read the ccna book that i bought from sybex page by page? I...
View ArticleARP learning
Hi All, Want to understand how multiple MAC address are on GigabitEthernet0/0/3 in arp table. Ip address 10.1.103.1 ,10.1.103.2 and 10.1.103.5 are configured on ABC device. ABC#sh ip arp vrf...
View ArticleCCIE Security v4 Practice Labs Workbook now released
Folks, While studying today my study partner noticed that within the last 10 minutes, INE has released the new CCIE Security v4 Practice Labs workbook.We also now have new IEOC forum sections for the...
View ArticleLab 5 ticket 7
Instead of adding igmp helper on r5, I removed ip pim neighbor-filter 1 on r5 to re-establish the pim nei b/w r1 and r5, I don't think this breaks the rule. Comments?Rack1R1#sh ip pim neiNeighbor...
View ArticleDHCP SERVER
I have two multi layer swicth like sw1 and sw2. All hosts connected to sw1 in vlan 10, sw1 has SVI of vlan 10. sw2 is DHCP server and it has no SVI. If any client send DHCP REQUEST for ip address, DHCP...
View Article8.4 Compression
Would "compress lzs" also work as a solution? SG had "compress stac". Thanks
View ArticleAverage age of CCIE prospect's first lab attempt?
Hello all...just joined the forum and this is my first post...I am not sure if there are actual statistics showing the average age of prospective CCIE's first attempt, but I am about to retire from the...
View Article5.3 Multicast Testing - Recreate my environment
Hello community,For some reason I cannot tell, I am unable to ping VLAN4 multicast group from VLAN52 but I can from R1 or R3. Also, the RP R2 is not functioning for any of its groups even though the...
View ArticleLab 4 solve time
Hello,How much time do you take to solve full scale lab 4?For me 8 hours are not enough, what about you?
View ArticleWBII - Task 3.2
3.2 IPv6 Multicast BasicsConfigure R6 to join the multicast group FF06::6 on its connection to R4.Configure R4 to accept MLD messages only for the group range FF06::/16.Use R5 as the PIM RP and ensure...
View Articleipsec vti issues
Could someone kindly give this a once over. For some reason my Tunnel is not coming up (remains up/down). R1crypto isakmp policy 1 encr 3des authentication pre-share group 2crypto isakmp key BLAH...
View ArticleDual-home site PE-CE routing
Hi Consider a dual-homed site, CE1----PE1---PE2---CE2 with the CE's connected via backdoor link and with RIP as the PE_CE routing protocol. Routes are advertised from PE to CE1 via redistribution....
View Article