Clik here to view.
EIGRP Queries
In EIGRP, when we lose a successor for a route, and no feasable successor exists, the router sends a multicast Query to its neighbors asking for the route each receiving router replies with a unicast...
View ArticleINE Forum Support
Hey All,Do INE tech people still post on the forums? I have not seen the instructors post recently? The community is great, but that is because of the members, not INE.Specifically I would be...
View ArticleCisco stops CCDE ???
One thing is striking my mind again n again and it is that " with softwares available and u just give input like for e.g if I have 2000 users and they sit in office in 7 floors it would be very easy...
View ArticleUCS CIMC/IPMI/KVM
Hi guys,I was wondering if anybody can help me understand CIMC and IPMI properly? How does KVM work and what does it use? What does management IP address in Service Profile apply to?Regards,AB
View ArticleiSCSI Boot
Hi, Just wondering can we do UCS boot from iSCSI , topology looks like UCS---FI--FC Link---MDS---FC Link---JBOD ... please suggest !!
View ArticleEIGRP Router-ID problem on External Route
Hi,Please see the link below. I was putting a lab together for testing, and basically R2 receives the external eigrp route for 34.34.34.0/24, but R1 doesn't. The problem was the originating router-id...
View ArticleTask 5.4 - r4 & r5 receives no mroute and rp info
Does anyone able to receive RP information on R4 and R5? I know the task didn't ask to check for RP but if it is working, we should see RP on R4 & R5.In addition, to make the IPv6 static route for...
View Articlehow to flush route profile
Hello Folks, On a routing table, some prefixes are withdrawed and installed back and forth, over and over again, several times per second. I know to address this routing issue, but I would like to...
View ArticleTask 7.1 Thresholds
Since questions is asking When there are more than 750 packets in the output queue, R1 should generate the message “WARNING: Frame Relay Circuit Congested”.SG looks good as it has to rise above...
View ArticleSP Lab 1st attempt failed
Took the SP Lab in RTP yesterday and things did not go well.First off at the very start of the exam was a troubleshooting step to get some IGP working. I fixed up obvious errors but ran into two XR...
View ArticleQOS on Fa0/0 interface [ internet & MPLS traffic ]
Hi Experts,Need your suggestions:Scenarion ====== LAN 100 MB | Router | WAN======= 8 MB [ 4MB & 4 MB MPLS Tunnel ]I have a connection to ISP with 8 MB bandwidth , 4 MB is internet and 4 MB mpls...
View ArticleThoughts on pre-configuration analysis approach
If anyone is willing to share, I'd like to hear other people's thoughts on the best way, or good ways, to approach the pre-configuration analysis when doing a lab. If anyone isn't familiar with what...
View ArticleOSPFv2 LFA Fast Reroute
All,I was wondering if anyone has successfully setup either OSPFv2 Loop Free Alternate Fast Reroute (single or multi-hop) in GNS3. It's part of the RS v5 Lab Topics and need to test it out. If yes,...
View ArticleClik here to view.
Multicast: Auto RP not Working
Hello community,For some reason I can't get SW2 to hear advertisements from the mapping agent (R1) or learn RP info. I also configured it to be a candidate RP and the maping agent is not getting its...
View ArticleTask 2.3 Default routing - solution incomplete
Task asks us to have R3 originate a default route into OSPF as long as it has an active connection to either BB2 or BB3. The solutions guide used a route-map which checked for the presence of the...
View ArticleTask 3.3 - Bridging over FR
Did anybody else run into an issue here? I configured it as I knew how to, looked at the SG and it was the same, but can't get the interface to pass traffic. It looks like it's going out, and appears...
View ArticleTask 3.3 potnetail solution
Does anyone see a problem with this as a solution. Trying to think why this would be a problem and i can't...bridge irbbridge 1 protocol ieeebridge 1 route ip!interface Serial0/0/0encapsulation...
View ArticleCSC technology
Just started going through this and i can't shrug off the feeling that it is seems bit odd design in the real world, I would imagine most people would rather purchase a L2 service from the backbone...
View ArticleClik here to view.
Michael Marx, CCIE #42713 (R/S)
My apologies for the length, but I have imagined writing this post for about a year now. I am sure it littered with typos - btu now its too long to proof... Frequently while I was studying I would...
View ArticlePrivilege level help
I'm having some trouble with setting privilege levels for a test user in my lab. I am trying to set my test user to have privilege level 1 in user exec and in priv exec mode so I setup the user and the...
View Article