Task 2.4 BGP Traffic Enginnering
Hello Experts,Whilst I agree that the solution for this task as recorded in the SG is correct i.e using aggregate and unsuppress-map to make traffic coming to VLAN5 to travel via the link between R4...
View ArticleSwitch Reloads and Loses Config
Hey guys, does anyone know why a switch would lose configuration after reloading? Startup-config is in NVRAM but somehow all goes away after a reload. My search on this only gives me issues with...
View ArticleMulticast over Inter-AS MPLS
Hi, I am working on a project that requires multicast over Inter-AS MPLS. I would greatly appreciate if any could cast their eye over the following and confirm if I am on the right track: Overview:*...
View ArticleOSPF COST CALCULATIONS
hi all,I am working through the INE WB1 and (due to confusing myself) had to go away and do more examples to try understand the way that the metric/cost is made up.I think I have a "technique" for...
View ArticleWill IS-IS and multicast be soon obsolete ?
Will IS-IS and multicast be soon obsolete ??? as I am learning these technologies and want to know that these technologies will be used for sometime .
View Article3.2 stateless autoconfig
I thought the command "ipv6 nd prefix 2001:CC1E:1:6::/64" is needed for stateless autoconfiguration. Comment?
View ArticleBGP traffic Passing via cisco ASA
R1 (2.2.2.2)------------ASA-------------R2(1.1.1.1) (INSIDE) (Outside)R1 and R2 are correctly configured for ebgp.On ASA :- Please correct by understanding1)If...
View ArticleINE's CCIE R&S Training program updates
Hello INE,Is there any updates coming to the following INE training program after change to v5.http://blog.ine.com/2010/10/09/how-to-pass-the-ccie-rs-with-ines-4-0-training-program/Do we need to wait...
View Article5.24 EIGRP Filtering with AD
Hi All,Can anyone explain why i am getting AD = 0 after applying distance command specifically for 150.1.4.0/24. Configuration as given below:Rack1R6#sh run | se router eigrprouter eigrp CCIE_AS_100 !...
View ArticleCCIE Security v4
Hi all, I am just about to start my CCIE security studies, but wanted to know about versions? is there a v5 on the horizon? or will v4 be around for a while?
View Article5.26 - alternative?
The only one I did differently here was:•Configure R4 to redistribute the VLAN 43 subnet into EIGRP with the tag value of 4.SG answer is:router eigrp 100 redistribute rip metric 100000 100 255 1 1500...
View ArticleAutomatic reply: EIGRP Queries
Dear sender, We are on public holiday untill 24 March 2014In urgent cases you can can Call/SMS me . Best Regards Kayssar
View ArticleClik here to view.
discard routes internal and external on NSSA ABR ?
link between r1 and r2 is in area 0.(10.1.1.0/30)link between r2 and r3 is in area1.(10.1.1.5/30)link between r3 and switch(i.e f0/1) is running rip.(20.1.1.1)area 1 is nssa.all routers have a loopback...
View ArticleBridging T1 to Ethernet
Hello Experts, I have a question for y'all. I'm trying to see if it is possible to bridge a T1 or DS3 site over to ethernet with the end goal of terminating it on a ASA Service Module.Here's my...
View ArticleAutomatic reply: Switch Reloads and Loses Config
Dear sender, We are on public holiday untill 24 March 2014In urgent cases you can can Call/SMS me . Best Regards Kayssar
View ArticleTask 7.3
Guys,I am not able to assign R4 IP address 139.1.45.4. I have spent hours now strugling with this task but was not able find a solution. I am persuaded it's an IOS bug.Did anyone make it work?There is...
View ArticleNeed help for Fiber GLC-LH-SM connection between Cisco 3750
Please help me. I want to connect my two Cisco 3750 switch by gbic GLC-LH-SM .Unfortunately, when i trying to connect,it's not uplink. More information about two switch below:Gi1/0/51 notconnect 1 auto...
View ArticleFull Scale CCIE DC labs
When is INE Going to release full scale DC labs. Nobody is Providing any tentetative schedule for full scale labs release.At least for CCIE Security INE is saying that they will start releasing Full...
View ArticleGNS3 running on Ubuntu
Hello, could anyone please explain the best way to configure GNS3 on Ubuntu, preferably in non super expert Linux speak? I've tried it on my windows machine and it sucks. There's too many posts on...
View ArticleClik here to view.
Issues with multicast traffic
I am having an issue getting multicast traffic down to the phone on the bottom of the graphic.Based on default priority values CORE2 should be the DR for the vl802 segment which means that it should be...
View Article