Is the topology diagram an "implied task?"
I was reading one of the INE blog posts regarding overconfiguration and it prompted this question.Would implicit configuration also include the topology diagram? For example, if loopback4 is shown in...
View Articlehow to select eigrp metric while redistributing
HI. how to decide what eigrp metric to choose while redistributing? specially when you've 2 or more routers doing ospf to eigrp or/and rip to eigrp redistribution?
View ArticleCCIE Lab access server send *
In my home lab I use send * from my access server all the time to send multiple commands to multiple devices. In the actual lab could these commands go to the backbone routers and cause any issues...
View ArticleCCIE R&S #42762
I have successfully completed CCIR R&S in San jose on 10th march. This was my first attempt. It was very good experience. I have 7 years of experience in Network. I am taking care of...
View Article12.3 Syslog Logging
Another way to test syslog config. Trigger sylog message using "send log <string>"; more TCLSH friendly.Side note: generate multicast traffic:1) Also observed that "logging host 239.1.1.2...
View ArticleTask 2.5
I don't understand why we can't use:router ospf 1distance ospf external 171 on sw2 and r3. In the solutions it says that:"SW2’s EIGRP adjacency to become active after it has learned the RIP prefixes...
View ArticleFCoE Questions
I have a couple of FCoE questions. The first is I’d like to verify my understanding of the difference between the FC NPV and FCoE NPV features. My understanding is in order to support both FC/FCoE...
View ArticleTask 2.7
How do we know to deny the aggregated BGP prefix to ibgp neighbors in this task? Should it be assumed in real lab to always deny the aggregated route on the internal network and only advertise it out...
View ArticleLab 1 Task 4.3 L2VPN
I would appreciate some help with this, I am not able to get the interworking L2VPN on R1 & XR2 (between R7 & R8) working. All the verificatons pass but the circuit will not pass broadcast or...
View Articlerunning 30 routers in gns3 ubuntu
Hi. how to run 30 routers in gns3 ubuntu? my pc hangs up once i reach 15 routers.
View ArticleIPv6 not abale to enable at interfaces
Dear All,I faced an issue in configuring Global IPv6 add in the router interfaces, I am able to configure link -local addresses without any issue.any idea, is there any other command required to enable...
View ArticleIssue on 2.4 Section in Vol2 Lab3
Hi all,The task to use weight attribute in Vol2 Lab3 Section 2.4, find difficulty while implementing it in the router.Inially i match the VLAN29 segment using standared ACL, once implemented i could...
View ArticleClik here to view.
Redistribution
please check the attached topology, i want to deny the 1.1.1.1/32 network going thro ospf domian now the goal is to use distribution-list. first i create Acl with deny statement of 1.1.1.1/32 then...
View ArticleN2k -- Catalyst Switch
Hi, I am curious to know can we connect N2k downstream to any CICSO access switch such as 2960 and trunking or allow multiple VLAN etc ... i know this no tht best practise desgin guide but customer...
View ArticleCisco 871 NAT Loopback
Hello All,I have a 871 router with two TCP ports allowed inbound to 22 and 80. I have setup what I will call a traditional NAT environment using "ip nat inside/outside" and static NAT entries for the...
View ArticleNetwork/Security Engineer - Las Vegas, NV
Looking for an experienced CCIE/CCNP/CISSP professional to fill an opening located at our headquarters in Las Vegas, NV. Position will configure and support our Cisco firewalls and IPS’s as well as...
View ArticlePlanning to cancel CCIE SP LAB
Dear friendsMy lab date is 5 may 2014And my wife's baby delivery date will be at that period only therefore I am planning to do special request to cisco to postpone my lab Can you pls suggest how to...
View ArticleClik here to view.
Frame Relay Prep.
Hi guys,I am preparing for CCIE v5 and i'm wondering if i need to remove all frame realy topics from my prep. ??I mean guys i am not going to be tested on it or even troubleshooting it?!! so,i wonder...
View ArticleThoughts on pre-configuration analysis approach
If anyone is willing to share, I'd like to hear other people's thoughts on the best way, or good ways, to approach the pre-configuration analysis when doing a lab. If anyone isn't familiar with what...
View ArticleOSPF COST CALCULATIONS
hi all,I am working through the INE WB1 and (due to confusing myself) had to go away and do more examples to try understand the way that the metric/cost is made up.I think I have a "technique" for...
View Article