configure connectivity on nme-cue
My nm-cue died and all we have as a replacement is a nme-cue. I tried to apply the current config from the nm-cue to the nme-cue and I can't ping it from the router to the nme-cue.This was the working...
View ArticleVRF aware GETVPN
Hi,I’m trying configure VRF-aware GETVPN. With FVRF global and set IVRF I don’t have any problems (communication between KS and GMs is in global VRF, only ‘business’ traffic between GMs is tagged). I...
View ArticleAdvice on ISR G2
Hi,I'd like to scale my lab with a mix of ISRs G1 & G2.My question is about 1921 vs 2911. The main concern is fan noise.As we know 1841 is very quiet, does anybody know if 1921 is quiet too? We...
View ArticleGNS3 on Ubuntu and Vol. 1 BGP
Hello all,I have had great success running all of the topologies so far for Vol 1. using an Ubuntu VM with 6GB RAM allocated. No problems at all.However, I loaded the BGP .net file (Initial BGP) and...
View Article2.5 - IGP Redistribution (Extra steps in solution??)
I have been working on this lab and have a question regarding the AD manipulation in the workbook solution document. When EIGRP is redistributed into RIP on SW1, the metric is set to 15 to prevent BB3...
View Article2.7 BGP Summarization
I've got a issues/question with the 2nd part of the section 2.7 BGP Summarization. Here is the part:Create an additional Loopback interface on SW1 using the 148.X.177.0/24 subnet and advertise it into...
View ArticleDynamips
Hello,Is it possible to use Dynamips to simulate a basic lab environment, i.e. AP/WLC/SWITCH?Do INE have any plans to provide lab racks for wireless?Cheers
View ArticleInteresting IPv6 Question
We all know that NAT is not there in IPv6 but still there is a private range of IP v6 addresses (Unique local address), so what would be the solution if we need to translate our IPv6 private IP v6...
View ArticlePPP CHAP callin/callout/callback
Could someone please explain how ppp authentication chap callin/callout/callback is working exactly? I read through all the cisco documentation, but didn't find any useful information regarding them....
View ArticleCCIE v5 Topology
I know Brian just mentioned v5 written and lab material in the works. Has anyone created their own v5 topology? I have grown accustomed to the v4 R&S topology with FR but I am interested to see...
View ArticleTask 2.2 Eigrp
I have some problem with follow target:Configure SW2 so that hosts in VLAN 8 use VLAN 18 to reach all hosts with an even number in the third octet, while VLAN 58 is used to reach all hosts with an odd...
View ArticlePerforming BGP load-sharing
All, I am looking for a way to perform load sharing from two routers to two different ISP's. I thgouht about using OER/PfR...also about PBR..but I want something dynamic..OER maybe?? If anyone is aware...
View ArticleRestarting UCCX 7
Hi I recently started Module 19 of Workbook I volume 3.5. There is a section that requires TS with the activation of services with the UCCX servicablity tool. After which you are meant to reboot the...
View ArticleNo v4 R&S Lab Seats In USA
Some of you may know this, others not, but there are no more available USA lab seats for the v4 blueprint. San Jose and RTP are booked full until June. Just throwing it out, as I was unaware. On the...
View ArticleChecking a router's memory space
Hello community,I am aware routers have different types of memories: RAM, NVRAM, ROM, and Flash and the following output is used to check amount of memory:Flash: I can see how much flash I have by...
View ArticleOVER CONFIGURATION IN TROUBLESHOOTING
Hello Guys, my query seems to be similar to the one i asked the last time but a bit different. Now is it possible to over configure in the troubleshooting aspect of the lab and yet not break any rules...
View ArticleOSPF Path Selection Question
I have a OSPF Path selection question, I understand that OSPF has some native path selection rules that cannot be overridden by metric or AD;Such as O is preferred over OIA, is preferred over E1, over...
View ArticleDifferent device pools for different types of devices?
Hi everyone, I'm watching Mark's videos on CIPT2 and healready said multiple times that he typically creates 2 device pools at a minimum for each site: one for phones & one for gateways. But he...
View ArticleTASK 3.4
3.4. PPP• Configure PPP on the Serial connection between R4 and R5.• Use IP unnumbered for this connection and use the most reliable interface.• Disable /32 prefix generation After using the...
View ArticleCCNP SP: SPEDGE Study Blog
I have passed CCNP ROUTE and will be pairing that along with CCNP SP EDGE, SPCORE, and SPADVROUTE to complete my CCNP SP. I need to use ROUTE as my SPROUTE replacement by spring 2015, but I have plenty...
View Article