Guys,
I'm trying to put a Terminal Server in the network where I am working, but it is not working.
I've connected the cable to the console ports on each device and then create the hosts entries on the TS Server, but the problem is, how can I know which line is connected to each device ?
CKM-TS-01#show line
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
0 0 CTY - - - - - 0 0 0/0 -
1 1 AUX 9600/9600 - - - - - 0 0 0/0 -
2 2 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/0 3 TTY 9600/9600 - - - - - 0 3 2251/0 -
0/0/1 4 TTY 9600/9600 - - - - - 0 11 0/0 -
0/0/2 5 TTY 9600/9600 - - - - - 0 0 0/0 -
* 0/0/3 6 TTY 9600/9600 - - - - - 0 400952 18362694/0 -
0/0/4 7 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/5 8 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/6 9 TTY 9600/9600 - - - - - 0 6 6319/0 -
0/0/7 10 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/8 11 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/9 12 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/10 13 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/11 14 TTY 9600/9600 - - - - - 0 12 4261/0 -
0/0/12 15 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/13 16 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/14 17 TTY 9600/9600 - - - - - 0 0 0/0 -
0/0/15 18 TTY 9600/9600 - - - - - 0 0 0/0 -
* 388 388 VTY - - - - - 8 0 0/0 -
389 389 VTY - - - - - 0 0 0/0 -
Tty Line Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
390 390 VTY - - - - - 0 0 0/0 -
391 391 VTY - - - - - 0 0 0/0 -
392 392 VTY - - - - - 0 0 0/0 -
393 393 VTY - - - - - 0 0 0/0 -
394 394 VTY - - - - - 0 0 0/0 -
395 395 VTY - - - - - 0 0 0/0 -
396 396 VTY - - - - - 0 0 0/0 -
397 397 VTY - - - - - 0 0 0/0 -
398 398 VTY - - - - - 0 0 0/0 -
399 399 VTY - - - - - 0 0 0/0 -
400 400 VTY - - - - - 0 0 0/0 -
401 401 VTY - - - - - 0 0 0/0 -
402 402 VTY - - - - - 0 0 0/0 -
403 403 VTY - - - - - 0 0 0/0 -
Line(s) not in async mode -or- with no hardware support:
19-387