Cisco IP Communicator
Hi; I'm working on the CUCM and have installed Cisco IP Communicator 8.6 on my laptop. my IP Communicator tries to register to the CUCM, but it is unsuccessful, because of the lack of knowledge about...
View ArticlePassed CCIE R&S
Today I passed my lab in Brussels... One of the greatest feeling of my life... Ferenc KurisCCIE #46451
View ArticleBGP Communities
On AT Labs in the BGP communities. I dont think I understand why we need to configure R1, R3 and R6 with the route-map. After you configure R5 to send the community to neighbor R4. R4 will send that...
View ArticleClik here to view.
Routes are crazy
Hi,Look at the image below people,i have set two static default routes on R3 overwriting the routes wich were installed by dhcp,my routes are like that: ip route 0.0.0.0 0.0.0.0 189.20.0.1ip route...
View ArticleUCS Technlogy labs - Rack rental
Dear All,I have been using INE CCIE DC Rackrental for practicing UCS technology Labs but I am not able to finish the all the sections in the lab time allocated for me. For example my time ended after I...
View ArticleR&S Rack rentals pcap export
Hi guys, I wanted to run capture on the R&S rack rental devices and export them to Wireshark. Same way as per Training videos either to VM host or my PC at home. I tried to clear this with the INE...
View ArticleIPSEC NAT-T
going over ipsec nat-ttopology is simpler1-------------r2-----------------r3r2 does PAT for the ip address of r1.I was trying to see the effect of disabling nat transversal on either r1 and r3, as per...
View ArticleClik here to view.
TE tunnel with specific BW requirement doesn't come up.
Hello,I have this setup:PE1 router is connected to P1 router via single 1G Intf. P1 router is in turn connected to the P2 router via 8xSTM-1, and finally P2 is connected to PE2 via single 1G...
View Article!!!! RD vs RT in mpls !!!!
Hi Please help me out regarding the difference between RD and RT.As per documents they state RD will be mapped to bgp attribute to avoid duplicity of ip address because mp-bgp is the best protocol to...
View ArticleCSR1000v CLI Doesn't Work Correctly
I'm running ESXi ver 5.1 on a Dell with 2 Xeon quadcore 5530 with 72Gb of RAM.I'm running two CSR1000v versions from my CCO download to try to get them to...
View ArticleBGP filtering in/out: Filter-List vs Prefix-List vs Route-Map
Hoping to get some expert advice regarding BGP filtering: neighbor x.x.x.x filter-list<as-path acl 1-500> in/out neighbor x.x.x.xprefix-list<prefix name> in/out neighbor x.x.x.x...
View ArticleCSR1000v on VMware workstation or VirtualBlox - issues so far
Hello folks, I have been running CSR1000v downloaded as a trial from cisco.com.It really seems the initial setup and boot process was easy. I am using it with GNS3 v1.2.1.However I have been running...
View ArticleOSPF nssa-only question
I am slight confused by the default behaviour of OSPF when it comes to setting the on an Type7 LSA. My understanding is that when the P bit is set then the LSA7 can be translated back to LSA5 by any...
View ArticleRetake policy in CCIE labs
Hello everyone, Since the last changed introduced in the lab retake policy, if you fail 2 times a lab attempt you have to wait for 3 months to be able to sit again on your 3rd attempt; I have a...
View ArticleGetting started with my labs
Hi I have gone through the ATC and looking for suggestions on my next step working towards my CCIE labs. I took the v4 Written exams last year. I plan on more reading and videos along the way but...
View ArticleChina site to site vpn internet traffic
I just started working with a client that has an office in the US and an office in China. They are having issues with Chinas big firewall :) blocking access back to some of their sites. Right now they...
View Articleroute-tag list
Hi; I'm working on the new "route-tag list" command. I have created this route-tag list to group all the tags between 10.10.10.0 to 10.10.10.255 and use it while redistribution. besides I have some...
View ArticleInitial configs question
I just started on the AT RIP labs, and noticed that the provided initial configs (initial rip & basic rip) use 169.254.100.0/24 addresses for the dmvpn cloud. Not a huge problem, since we can...
View ArticleHas anyone used the CCNP:Workbook?
I'm having a great deal of difficulty with it, not in the sense of having trouble with the material, but in the sense "these configs are broken, and the text doesn't match either the starting configs,...
View ArticleCisco Memory Question
Hi All,I just had to install some new DRAM for a 2951. After installation, I just have some queries from the #sh cmd's. I have put two 2GB DRAM sticks in (i.e. 4GB total). So in the sh ver output, I...
View Article