Clik here to view.
INE Lab - MDS3 and MDS4
Hi Guys,I need your advise on two point here.Point 1: I can see from the INE LAB topology diagram that there is MDS3 and MDS4 but I am not really sure how to connect to these MDS (3&4) and if we...
View ArticleNew WB for RSv5 - non-covered topics
Hey INE guys,just want to ask - I went through the new workbook and have observed that there is new topology that is Layer3 based (maybe some L2/L3 switch for creating the links between routers). Then,...
View Article4.1
PE-CE config on BB1...I've taken a look at BB1 but there is no PE configuration on it relating to this PE-CE relationship. Am I missing something?How am I meant to get a eigrp peering to work over a VRF?
View ArticleTask 5.1 PIM Filtering
Task 5.15. MulticastSome of the multicast settings have been pre-configured for you. You need todiscover the active multicast topology using the show commands.5.1 PIM Filtering - A media server located...
View ArticleLab INE
I am curious to how some of your guys are building your INE topology LAB,are you using gns3 with XR routers in virtual box?Are you using the new gns3 with IOU?What are you using for the ME switches
View Article6.2
SG output is:SW3 and SW4:mac access-list extended DEC-SPANNING permit any any dec-spanning!vlan access-map NO_DEC-SPANNING 10 action drop match mac address DEC-SPANNING!vlan access-map NO_DEC-SPANNING...
View ArticleASA SMTP inspection task
Guys, i have a few comments on the above task:- In the solution, the domains cyberscam.org and nullroute.com are added as follows in regex: "(cyberspam.org|nullroute.com)". I think it must be...
View ArticleASA Threat Detection task
Dears,I have a question in the above task. I understood that the burst_rate is calculated by the formula (1/30)*rate_interval.Rate_interval=7200 seconds. Then the Burst_rate will be 240. Why in the...
View ArticleMissing Topics in CCIE Sec V4 ATC
There are some Topics missing in CCIE Security V4 ATC like NAT on ASA 8.4/8.6,IKEV2,VRF aware VPN,GETVPN etc so Brain or Cristian i would be really thankful to you if you Guys can update us that when...
View ArticleThe Avenginator Returns.
Lets get the nasty bits over with.No I'm not a CCIE...I failed....TWICE! Shame on me but those who followed my posts previously had an idea that I was well on my way to passing this thing...or at...
View Article10.81 Advanced HTTP Classification with NBAR
Hi experts,according to my testing, this SG statement is not true:"Matching is case-sensitive and you can use patterns like [aA] to match both cases."This also contradicts what is said in 11.12 Using...
View ArticleV5 rack rental and IPv6
HiI was wondering if anyone has tried a full dual-stack deployment on the new v5Racks? I was running into an ND error where the Routers could not resolve or communicate with ipv6. I tested my config on...
View ArticleCoPP configuration
hi we are seeing Copp violation packet in CoPP is that fine. should we need to increase the bandwidth set. we dont see CPU high though.thanks in advanceclass-map copp-system-class-important...
View ArticleClik here to view.
Security Lab 5 - section 3.1 R3 Sub-Ca not working
Support, we follow your detail solution for Lab 5, but the R3 Sub-Ca not working, has below error, what's wrong? Please advice............
View ArticleCSR1000v - debug ip packet does not work?
Hi,A few days ago I have set up the new v5 topology using 10 CSR1000v (03.11.00.S) and started labbing. It worked great, but today I ran into issue when trying to debug some GRE tunnels.I found that...
View ArticleTask 6.2 Traffic Filtering with Dynamic ACL (Lock & Key)
Guys,The task says "Configure the network in such a way that hosts must first authenticate to R2 before they are allowed to telnet to SW1". Doesn't it mean that we need to use the "host" keyword in...
View Article7.4
Configure SW2 to respond to UDP echoes from a network management station with a yet unknown IP address.SW2 should not respond to packets sent to the UDP discard and chargen ports from this network...
View ArticleMy fifteen hundred dollar lunch.
Failed troubleshooting, passed configuration. I got smoked on the troubleshooting section. My suggestion is like people say regarding config, read all the tickets before starting, there are...
View ArticleNew INE 10-Day CCNP Routing & Switching Bootcamps!
Hi everyone,Just wanted to let you know that INE has just released CCNP Routing & Switching 10-Day Bootcamps! Both live on-site and online interactive Bootcamp formats are available for purchase....
View ArticleQuestion about IP MTU.
Hi Experts,I have network connected like this: R1(Fa0/0) - (Fa0/0)R2R1 Fa0/0 interface is configured for ip mtu 1498.Now sending a ping with packet size of 1500 from R1 to R2.The packet from R1 to R2...
View Article