Quantcast
Channel: IEOC - INE's Online Community
Viewing all articles
Browse latest Browse all 10744

RIP 4.10

$
0
0

TO DO THIS TASK , PREVIOUSLY I SHOULD GET THE ETHERCHANNEL UP ,BUT IT'S FLAPPED . SO KINDLY ADVICE.

*Mar 20 08:37:52.206: %LINK-3-UPDOWN: Interface Port-channel1, changed state to up

*Mar 20 08:37:52.214: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel1, changed state to up

*Mar 20 08:37:52.970: %LACP-4-MULTIPLE_NEIGHBORS: Multiple neighbors detected on Et3/2: new neighbor(sys-mac-id: 0200.3000.0800, port: 0x401), old neighbor(sys-mac-id: 0200.3000.0800, port: 0x403)

*Mar 20 08:37:52.986: %LINK-3-UPDOWN: Interface Port-channel1, changed state to down

Rack1SW4#sh run int port-channel 1

Building configuration...

Current configuration : 85 bytes

!

interface Port-channel1

 no switchport

 ip address 155.1.108.10 255.255.255.0

end

interface Ethernet3/0

 no switchport

 no ip address

 duplex auto

 channel-group 1 mode active

!

interface Ethernet3/1

 no switchport

 no ip address

 duplex auto

 channel-group 1 mode active

!

interface Ethernet3/2

 no switchport

 no ip address

 duplex auto

 channel-group 1 mode active

Rack1SW4#sh etherchannel summary 

Flags:  D - down        P - bundled in port-channel

        I - stand-alone s - suspended

        H - Hot-standby (LACP only)

        R - Layer3      S - Layer2

        U - in use      N - not in use, no aggregation

        f - failed to allocate aggregator

 

        M - not in use, no aggregation due to minimum links not met

        m - not in use, port not aggregated due to minimum links not met

        u - unsuitable for bundling

        d - default port

 

        w - waiting to be aggregated

Number of channel-groups in use: 1

Number of aggregators:           1

 

Group  Port-channel  Protocol    Ports

------+-------------+-----------+-----------------------------------------------

1      Po1(RD)         LACP      Et3/0(w)       Et3/1(w)       Et3/2(w)       

==================

Rack1SW2#sh run int port-channel 1

Building configuration...

 

Current configuration : 84 bytes

!

interface Port-channel1

 no switchport

 ip address 155.1.108.8 255.255.255.0

end

interface Ethernet4/0

 no switchport

 --More-- 

*Mar 20 08:43:04.430: %EC-5-L3DONTBNDL2: Et4/1 suspended: LACP currently may not be enabled on the remote port.

 no ip address

 duplex auto

 channel-group 1 mode active

!

interface Ethernet4/1

 no switchport

 no ip address

 duplex auto

 channel-group 1 mode active

!

interface Ethernet4/2

 no switchport

 no ip address

 duplex auto

 channel-group 1 mode active

*Mar 20 08:43:17.430: %EC-5-L3DONTBNDL2: Et4/0 suspended: LACP currently may not be enabled on the remote port.

Rack1SW2#sh etherchannel summary 

Flags:  D - down        P - bundled in port-channel

        I - stand-alone s - suspended

        H - Hot-standby (LACP only)

        R - Layer3      S - Layer2

        U - in use      N - not in use, no aggregation

        f - failed to allocate aggregator

 

        M - not in use, no aggregation due to minimum links not met

        m - not in use, port not aggregated due to minimum links not met

        u - unsuitable for bundling

        d - default port

 

        w - waiting to be aggregated

Number of channel-groups in use: 1

Number of aggregators:           1

 

Group  Port-channel  Protocol    Ports

------+-------------+-----------+-----------------------------------------------

1      Po1(RD)         LACP      Et4/0(s)       Et4/1(w)       Et4/2(w)       


Viewing all articles
Browse latest Browse all 10744

Trending Articles